Bailey Infi 90 IMDSM05 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 46

background image

INTRODUCTION

I-E96-309A

3 - 1

SECTION 3 - INSTALLATION

INTRODUCTION

This section explains what you must do before you put the Dig-
ital Slave Module (IMDSM05) into operation. DO NOT PRO-
CEED with operation until you read, understand and do the
steps in the order in which they appear.

NOTE: Refer to Product Instruction I-E93-911 for termination device
wiring instructions.

SPECIAL HANDLING

NOTE: Always use Bailey's Field Static Kit (P/N 1948385A2 - con-
sists of wrist strap, ground cord assembly, alligator clip) when work-
ing with modules. The kit is designed to connect a technician and
the static dissipative work surface to the same ground point to pre-
vent damage to the modules by electrostatic discharge.

The Digital Slave Module (DSM) uses electrostatic sensitive
devices. Follow Steps 1 through 4 when handling:

1. Keep the module in its special anti-static bag until you are
ready to install it in the system. Save the bag for future use.

2. Ground the anti-static bag before opening.

3. Verify that all devices connected to the module are properly
grounded before using them.

4. Avoid touching the circuitry when handling the module.

UNPACKING AND INSPECTION

1. Examine the hardware immediately to verify it has not been
damaged in transit.

2. Notify the nearest Bailey Controls Sales Office of any dam-
age.

3. File a claim for any damage with the transportation com-
pany that handled the shipment.

4. Use the original packing material and container to store the
hardware.

5. Store the hardware in an environment of good air quality,
free from temperature and moisture extremes.

«
...
18
19
20
21
22
...
»

Содержание Infi 90 IMDSM05















































Отзывы:

Нет отзывов

Похожие инструкции для Infi 90 IMDSM05

Бренд: Vacon Страницы: 62

Бренд: Watts Страницы: 2

Бренд: Lawler Страницы: 4

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Dahua Страницы: 58

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

Бренд: Harsco Industrial Страницы: 57

Бренд: Fingertips Lab Страницы: 15

S3500 Series Uplink Module

Бренд: Aruba Страницы: 8

Бренд: Lutron Electronics Страницы: 2

Бренд: Scanreco Страницы: 10

Бренд: Teledyne Страницы: 102

Бренд: OLYS Страницы: 4

The Boost Box WS 1107

Бренд: Watersports Innovations Страницы: 12

Бренд: Parker Страницы: 31

Бренд: Pixie Страницы: 21

Бренд: ApexWaves Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды