Bad Boy Mowers OUTLAW Скачать руководство пользователя страница 4

Страница: 4 / 72

PAGE 4

SECTION 1:

BASIC INFORMATION

Congratulations on the purchase of your new Bad Boy Mower! The purpose of this manual is to assist

operators in maintaining and operating their machine. The information and instructions in this manual can help

you attain years of performance from your new Bad Boy. Also, check out our website to learn more about the

Bad Boy family.
1.1

All Bad Boy engines use 10W-30 engine oil. For maximum protection, Bad Boy synthetic blend engine

oil is recommended.

1.2

All Bad Boy hydraulic systems use 20W-50 engine oil (Conventional or Synthetic). Bad Boy Hydrostatic

oil is recommended.

1.3

All Bad Boy Mowers use hi-temp multi-purpose grease. NLGI No. 2 for the grease fittings.

1.4

Outlaw models have 12 psi in both front and rear tires.

1.5

Most Briggs, Kohler, Kawasaki, and Vanguard engines hold approximately two (2) quarts of motor oil.

Be careful not to over fill engine oil. Refer to engine’s service manual.

WARRANTY REGISTRATION

The Warranty Registration form must be completed within 30 days to validate your warranty. As the new

equipment owner, you are expected to see that the form is completed and forwarded to Bad Boy Inc. at time of

delivery. Warranty is nontransferable. Warranty registration should be completed by the selling

dealership using the on-line registration site.

MODEL/SERIAL NUMBER

Your Outlaw model serial numbers are found on the SIN plate underneath the seat. These numbers can assist

you in the ordering of new parts when replacements become necessary.

PARTS/SERVICE

Only Bad Boy replacement parts are to be used on your mower. Replacement parts are available through your

local Bad Boy Mowers Dealer. Remember to always provide the following information when ordering parts:

Correct part number

Correct serial number

All warranty repair and service must be handled through your authorized Bad Boy Mowers Dealer. To locate

the nearest dealer, go to our website and click on Locate a Dealer.

EVAPORATIVE EMISSION CONTROL WARRANTY STATEMENT

Federal Evaporative Emission Control Warranty: Your Warranty Rights and Obligations

The Environmental Protection Agency (EPA), and Bad Boy Inc. are pleased to explain the evaporative emission

control system's warranty on your 2018 equipment. New equipment that uses spark ignition engines for off-

road use must meet stringent anti-smog standards. the evaporative emission control system on your

equipment is designed, built, and equipped so it conforms at the time of sale to the ultimate purchaser with the

requirements of 40 CFR 1060. The evaporative emission control system is free from defects in materials and

workmanship that may keep it from meeting said requirements. Bad Boy Inc. must warrant the evaporative

mission control system on your equipment for two years provided there has been no abuse, neglect, or

improper maintenance. If an evaporative emission control system component does fail in a manner that would

cause the equipment to no longer meet the requirements of 40 CFR 1060 within the first two years Bad Boy Inc.

will replace the defective component. Your evaporative emission control system may include parts such as fuel

tanks, fuel lines, carbon canisters, fuel caps, valves, vapor hoses, clamps, or connectors.

Содержание Mowers OUTLAW









































































Результаты поиска

Содержание Mowers OUTLAW

Отзывы:

Похожие инструкции для Mowers OUTLAW

Бренды по названию

Популярные бренды

Bad Boy Mowers OUTLAW, Руководство владельца, обслуживания и запасных частей

Результаты поиска

Содержание Mowers OUTLAW

Отзывы:

Похожие инструкции для Mowers OUTLAW

Бренды по названию

Популярные бренды