Backyard Products GABLE 10 x 12 Скачать руководство пользователя

Страница: 44 / 66

100

PARTS REQUIRED:

1" (2,5 cm)

5/16" (0,8 cm) Drill Bit

DOOR HARDWARE

BEGIN

Install bolt with screws supplied and drill 5/16" hole for bolt to extend into.

Place bolt on

in open position with bolt end 1/2" up from floor.

Bolt is open when loop is contacting base

(Fig B)

Place spring bolt on

in open position with bolt end 3/8" down from frame.

Bolt is open when loop is contacting base

(Fig A)

Mark and pre-drill holes for screws.

LEFT

DOOR

Fig. B

Your spring bolts are now installed.

Fig. A

FLOOR

Loop contacts

base.

1/2"

5/16" drill for

bolt: 1" deep.

Loop contacts

base.

PRE-DRILL

(4) HOLES

PRE-DRILL

(4) HOLES

69” (175,3) Door

Stiffener

69” (175,3)

Door Stiffener

3/8" with bolt in open

position.

OPEN POSITION,

Spring is loose.

OPEN POSITION,

Spring is loose.

5/16" drill for bolt:

1" deep.

OVER DOOR FRAME

LOCATE AND PRE-DRILL HOLES TO AVOID SPLITTING WOOD

FINISH

Содержание GABLE 10 x 12



































































Результаты поиска

Содержание GABLE 10 x 12

Отзывы:

Похожие инструкции для GABLE 10 x 12

Бренды по названию

Популярные бренды

Backyard Products GABLE 10 x 12, Руководство пользователя

Результаты поиска

Содержание GABLE 10 x 12

Отзывы:

Похожие инструкции для GABLE 10 x 12

Бренды по названию

Популярные бренды