Bacharach 100 Скачать руководство пользователя страница 25

Страница: 25 / 64

Instruction 24-9395

Fyrite Pro

4.2 Performing a Combustion Test using

the Model 110/120/125

4.2.1 Analyzer Turn On and Warm Up

Important:

The probe must be at room temperature before

performing the following steps.

1. Connect the probe and make sure that the analyzer s properly set

up per Secton 3.0.

2. Perform one of the followng:

•

Model 110/120

– Before turnng ON the analyzer, ts probe must

be located n the area contanng the burner’s combuston-ar sup-

ply. If the burner s usng room ar, smply place the probe wthn

the room. In the case of a hgh-effcency furnace where combus-

ton ar s drawn n from an outsde source, nsert the probe nto

the combuston-ar stream so t can measure ts temperature wth

the burner operatng.

•

Model 125

– Ths analyzer has a second thermocouple channel

that can be used to ndependently montor the temperature of the

burner’s combuston-ar supply. When usng ths second thermo-

couple channel, nsert the thermocouple nto the burner’s combus-

ton-ar stream, and poston the probe to measure the ambent

room temperature. If the second thermocouple channel s

not

used

, then use the probe’s thermocouple to measure the combus-

ton-ar temperature as descrbed above for the Model 110/120.

3. Turn ON the analyzer and allow t to warm-up per Secton 4.1.1.

4.2.2 Selecting a Fuel

1. Wth Fuel Screen dsplayed, use the





button to step through

the fuels codes untl the proper fuel s selected. The analyzer de-

faults to the most recently selected fuel.

F1 = Natural Gas

F2 = Ol #2

F3 = LPG

F4 = Kerosene

2. Press the

eNTeR

button to select the dsplayed fuel code and enter

the Run Mode.

Содержание 100

































































Результаты поиска

Содержание 100

Отзывы:

Похожие инструкции для 100

Бренды по названию

Популярные бренды

Bacharach 100, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 100

Отзывы:

Похожие инструкции для 100

Бренды по названию

Популярные бренды