Baby Lock imagine wave BLE3ATW Скачать руководство пользователя | Manualshive

Страница: 10 / 56

background image

After removing the packing materials from the box, gently lift your Baby Lock serger by gasping the handle
provided on the top of the machine.  Place the machine on a serger sewing table or any level surface that
provides ample work area to the left.  Place the foot controller in a pedal stay, if desired, and place it under
the sewing table.
Plug the power cord into the machine first, then into a wall outlet.  The power switch is located toward the
back on the right side of the machine.  Always make sure the power is off when the machine is not in use
(fig.A).
Available foot controller for U.S.A.: Model YC-482, or YC-420W
This appliance has a polarized plug (one blade wider than the other).  To reduce the risk of electric shock,
this  plug  is  intended  to  fit  in  a  polarized  outlet  only  one  way.    If  the  plug  does  not  fit  fully  in  the  outlet,
reverse the plug.  If it still does not fit, contact a qualified electrician to install the proper outlet.  Do not
modify the plug in any way.
The sewing speed of the machine is determined by the amount of pressure applied to the foot controller.
When not in use, do not place anything on the foot controller, or the machine could start inadvertently and
the controller or motor could burn out (fig.A).
Raise the telescopic thread guide to its highest position of 14".  Rotate the shaft to the left and right until
each section "clicks" into a locked position (fig.B).  The front cover may be opened simply by placing your
fingers behind the tab at the right side and pulling toward you (fig.C).
To open the cutting blade cover, place your thumb against the tab, and slide the cover to the right.  A slight
pull forward will allow the cover to swing down, providing access to the loopers, blades, and thread guides
(fig.D).

S
E

R

G

E

R

S
E

T

U

P

8

Setting Up Your Imagine Wave

A

B

C

D

O

A

B

C

D

«
...
8
9
10
11
12
...
»

Содержание imagine wave BLE3ATW

























































Отзывы:

Нет отзывов

Похожие инструкции для imagine wave BLE3ATW

Бренд: Xerox Страницы: 22

Бренд: Leather Machine Страницы: 4

Highlight MERCHANDISER 1RHCC30

Бренд: Zero Zone Страницы: 53

Бренд: DURKOPP ADLER Страницы: 49

Бренд: Singer Страницы: 99

Бренд: Singer Страницы: 47

Бренд: W6 Страницы: 281

UnionSpecial 36200UAD52

Бренд: JUKI Страницы: 64

Personal FAX-170

Бренд: Brother Страницы: 76

Бренд: Brother Страницы: 37

Бренд: Brother Страницы: 203

Бренд: Brother Страницы: 264

Бренд: Brother Страницы: 93

Бренд: Brother Страницы: 153

Бренд: Brother Страницы: 11

SC 7900-02 M6 A

Бренд: SunStar Страницы: 47

AFX LIGHT 15-175

Бренд: LOTRONIC Страницы: 11

Бренд: FAS Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды