Baby Lock imagine wave BLE3ATW Скачать руководство пользователя | Manualshive

Страница: 52 / 56

background image

T

R

O

U
B

L

E
S

H

O
O

T

I

N

G

50

Troubleshooting

Before taking your machine in for service, check the following:

Machine fails to start:

1. Are electrical plugs properly connected?
2. Is the power switch on?
3. Check household circuit breaker or fuse.
4. Is the lock button release lever in the unlocked position?

Thread breaks:

1. Is the machine threaded correctly? Check each thread path carefully.
2. Is the needle inserted correctly?
3. Is the needle bent and worn?
4. Is the stitch selector on the proper setting?
5. Are you using good quality thread?
6. Is the thread feeding off the cone/spool freely?
7. Is the needle size correct for the type of fabric being used?
8. Are the needles being used the correct Schmetz or Organ HAx1SP/CR system?

Skipped Stitches:

1. Is the needle bent or worn?
2. Is the needle inserted correctly?
3. Is the serger threaded correctly?
4. Is the presser foot pressure right for the fabric?
5. Is the correct needle being used for the particular stitch?
6. Is the correct needle being used for the type of being sewn fabric?
7. Is the fabric being pulled from the rear of the machine while sewing?

Fabric will not feed in machine:

1. Is the machine lock button released?
2. Is the presser foot down?
3. Are the cutting blades sharp?
4. Are the cutting blades, presser foot, and feed dogs free of lint?
5. Are the cutting blades properly set and is the upper blade against the lower blade?
6. Is the presser foot pressure right for the fabric?
7. Is the stitch length set properly?
8. Is the needle plate secure on the machine?

Stitch is Unbalanced:

1. Is the serger threaded correctly?
2. Is the stitch selector on the proper setting?
3. Is the thread well seated in the thread slots?
4. Is the looper thread fine-tuning screw positioned correctly?

Note: If you change the position of the looper thread fine-tuning screw and stitch is unbalanced, return

the screw to the standard position and recheck the stitch.(See page 13 for illustration.)

«
...
50
51
52
53
54
...
»

Содержание imagine wave BLE3ATW

























































Отзывы:

Нет отзывов

Похожие инструкции для imagine wave BLE3ATW

Бренд: N&W Global Vending Страницы: 23

Бренд: Panasonic Страницы: 88

Бренд: Janome Страницы: 68

INSIDE-FOG FLUID

Бренд: Safex Страницы: 8

Kaffe 770 QE PLUS

Бренд: Bernina Страницы: 236

Бренд: Oki Страницы: 128

Бренд: ROOTS Страницы: 164

GBC StreamPunch Ultra

Бренд: ACCO Brands Страницы: 92

Бренд: afx light Страницы: 19

Бренд: Zenit Powertools Страницы: 10

Firebase SG-Z1200

Бренд: FROGGYS FOG Страницы: 6

Бренд: AFXlight Страницы: 20

Бренд: JUKI Страницы: 6

Бренд: Singer Страницы: 2

Бренд: JUKI Страницы: 2

Бренд: JUKI Страницы: 8

Бренд: JUKI Страницы: 10

Бренд: JUKI Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды