Baby Lock imagine wave BLE3ATW Скачать руководство пользователя | Manualshive

Страница: 47 / 56

background image

U

S

I

N

G

S
P
E

C

I

A

L
T

Y

T

H
R

E

A
D

S

45

Bypassing the Threading Port

C

B

D

A

Heavyweight threads can be used through your regular looper
thread paths. Specific techniques may require that the thread
bypass the thread port for the thread pull to be loosened. Start
with the machine threaded with regular serger thread.

1. Open front cover and raise the presser foot.
2. Just above the threading port, clip the looper thread to be

replaced. Pull the thread out of the upper guides and remove
the cone.

3. Place the specialty thread on the spool pin. Thread it into the

upper guides and clip it a couple of inches beyond the base
plate (fig. A).

4. With machine lock button released, use the tweezers to pull

the existing looper thread out of tube extending from the
threading mechanism (fig. B). Leave the thread in the looper
arm.

5. Tie the specialty thread onto the regular thread with an over-

hand knot (fig. C). Pull on the regular thread from the looper
eye until the specialty thread comes through the looper eye.

6. Place upper looper thread under the foot and to the left: clip

lower looper thread at the base plate.

If the thread is heavy and the overhand knot (step #5) is too
large for the looper tube, follow directions #1 thru #6 on page
43 to make a thread cradle. Then:

1. Release machine lock button.
2. While holding the loose ends of the thread cradle with one

hand, use the tweezers to pull the cradle loop out of the tube
extending from the threading mechanism with the other hand.

3. Insert 2 inch(5cm) of your decorative thread into the cradle

loop. Pull on the loose ends of the thread cradle from the

looper eye until the specialty thread comes through the loop-

er eye.

«
...
45
46
47
48
49
...
»

Содержание imagine wave BLE3ATW

























































Отзывы:

Нет отзывов

Похожие инструкции для imagine wave BLE3ATW

Бренд: Janome Страницы: 41

Бренд: Pfaff Страницы: 122

Бренд: Foamit Страницы: 10

Бренд: Nilfisk-Advance Страницы: 39

Бренд: Unicum Страницы: 88

Бренд: JUKI Страницы: 140

Бренд: Riccar Страницы: 18

Бренд: Riccar Страницы: 28

Бренд: Riccar Страницы: 45

Бренд: Rhin-O-Tuff Страницы: 2

Бренд: Singer Страницы: 32

Бренд: Ice Страницы: 43

Бренд: ZOJE Страницы: 65

Бренд: Singer Страницы: 32

Бренд: Singer Страницы: 26

Бренд: Singer Страницы: 42

TINY TAYLOR TT600

Бренд: Singer Страницы: 10

TOUCH-TRONIC 2000

Бренд: Singer Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды