background image

Position the unit at the back of car headrest 

using the securing ribbon.

Plug  in  DC  power  jack  into  power 

port in base of unit.

Note

Note

2. Power Supply Connection & Operation 

 One can connect to a power supply using the following methods

8

9

3. In-Car Operation Procedure 

Setup

Setup

When first switched on there will be a slight mineral smell. This is perfectly normal and is due 
to special manufacturing technique of the NCCO Reactor.
The smell is harmless and will disappear after a period of time operating the unit.

Using  internal  battery

  –  Just 

press  the  ON/OFF  Button  and 

the  unit  will  start  using  its 

rechargeable lithium battery

.

Remove  base  plate  from  underneath 

unit.  Remove  4  screws  holding  ribbon 

securing  plates.  Place  and  locate  both 

free ends of ribbon and then screw back 

securing plates. Replace base plate.

Using  USB  power  cord 

–  Insert  USB 

connector into supplied power plug and 

connect to appropriate socket. Insert pin 

end of plug into the power port of main 

unit. This is located underneath the unit.

You can adjust ribbon tension by 

moving  ribbon  within  the  clip 

buckle.

② 

② 

If filters should not be installed into the unit, a ‘DiDiDi’ alarm sound will be heard from the unit. 
Please ensure that HEPA Filter and NCCO Reactor are properly installed prior to switching the 
unit on.

If using the unit in a mobile environment, please ensure that the unit is firmly fixed so that it does 
not ‘waggle’ or loosen when in motion.
If using the unit in a car, please follow the relevant country laws and regulations such as not 
placing free standing objects on the car centre console.

Please check and ensure that the car power supply is correct. The power input of this unit 
is DC 5V 2A.

Before operating unit in car, please make sure that the power supply has been disconnected 
and lift up unit carefully.

Please check and ensure that the car power supply is correct. The power input of this unit 
is DC5V 2A.

Using USB power source (car)

 – Insert USB connector into car USB port which will 

use charging power from vehicle.

(*Please ensure that ribbon has been tightened to 

prevent unit from waggling.)

Содержание NCCO1802

















Отзывы: