Azbil PTG71 Скачать руководство пользователя страница 80

We would like to express our appreciation for your purchase and use of Azbil Corporation’s products. 
You are required to acknowledge and agree upon the following terms and conditions for your purchase of Azbil Corporation’s products (system 
products, field instruments, control valves, and control products), unless otherwise stated in any separate document, including, without limitation, 
estimation sheets, written agreements, catalogs, specifications and instruction manuals. 
1.  Warranty period and warranty scope

1.1  Warranty period

Azbil Corporation’s products shall be warranted for one (1) year from the date of your purchase of the said products or the delivery of the 
said products to a place designated by you.

1.2  Warranty scope

In the event that Azbil Corporation’s product has any failure attributable to azbil during the aforementioned warranty period, Azbil 
Corporation shall, without charge, deliver a replacement for the said product to the place where you purchased, or repair the said 
product and deliver it to the aforementioned place.  Notwithstanding the foregoing, any failure falling under one of the following shall 
not be covered under this warranty: 

(1)  Failure caused by your improper use of azbil product (noncompliance with conditions, environment of use, precautions, etc. set 

forth in catalogs, specifications, instruction manuals, etc.); 

(2)  Failure caused for other reasons than Azbil Corporation’s product;
(3)  Failure caused by any modification or repair made by any person other than Azbil Corporation or Azbil Corporation’s 

subcontractors;  

(4)  Failure caused by your use of Azbil Corporation’s product in a manner not conforming to the intended usage of that product; 
(5)  Failure that the state-of-the-art at the time of Azbil Corporation’s shipment did not allow Azbil Corporation to predict; or 
(6)  Failure that arose from any reason not attributable to Azbil Corporation, including, without limitation, acts of God, disasters, and 

actions taken by a third party. 

Please note that the term “warranty” as used herein refers to equipment-only-warranty, and Azbil Corporation shall not be liable for any 
damages, including direct, indirect, special, incidental or consequential damages in connection with or arising out of Azbil Corporation’s 
products. 

2.  Ascertainment of suitability 

You are required to ascertain the suitability of Azbil Corporation’s product in case of your use of the same with your machinery, 
equipment, etc. (hereinafter referred to as “Equipment”) on your own responsibility, taking the following matters into consideration: 

(1)  Regulations and standards or laws that your Equipment is to comply with.
(2)  Examples of application described in any documents provided by Azbil Corporation are for your reference purpose only, and 

you are required to check the functions and safety of your Equipment prior to your use. 

(3)  Measures to be taken to secure the required level of the reliability and safety of your Equipment in your use 

Although azbil is constantly making efforts to improve the quality and reliability of Azbil Corporation’s products, there exists 
a possibility that parts and machinery may break down.  You are required to provide your Equipment with safety design such 
as fool-proof design,*

1

 and fail-safe design*

2

 (anti-flame propagation design, etc.), whereby preventing any occurrence of 

physical injuries, fires, significant damage, and so forth. Furthermore, fault avoidance,*

3

 fault tolerance,*

4

 or the like should be 

incorporated so that the said Equipment can satisfy the level of reliability and safety required for your use. 
*1. A design that is safe even if the user makes an error. 
*2. A design that is safe even if the device fails. 
*3. Avoidance of device failure by using highly reliable components, etc. 
*4. The use of redundancy. 

3.  Precautions and restrictions on application 

3.1  Restrictions on application

Please follow the table below for use in nuclear power or radiation-related equipment. 

Nuclear power quality*

5

 required

Nuclear power quality*

5

 not required

Within a radiation 

controlled area*

6

Cannot be used (except for limit switches for 

nuclear power*

7

)

Cannot be used (except for limit switches for 

nuclear power*

7

)

Outside a radiation 

controlled area*

6

Cannot be used (except for limit switches for 

nuclear power*

7

)

Can be used

*5. Nuclear power quality: compliance with JEAG 4121 required
*6.  Radiation controlled area: an area governed by the requirements of article 3 of “Rules on the Prevention of Harm from 

Ionizing Radiation,” article 2 2 4 of “Regulations on Installation and Operation of Nuclear Reactors for Practical Power 
Generation,” article 4 of “Determining the Quantity, etc., of Radiation-Emitting Isotopes,”etc.

*7.  Limit switch for nuclear power: a limit switch designed, manufactured and sold according to IEEE 382 and JEAG 4121.

Any Azbil Corporation’s products shall not be used for/with medical equipment.
The products are for industrial use. Do not allow general consumers to install or use any Azbil Corporation’s product. However, azbil 
products can be incorporated into products used by general consumers. If you intend to use a product for that purpose, please contact 
one of our sales representatives. 

3.2  Precautions on application

you are required to conduct a consultation with our sales representative and understand detail specifications, cautions for operation, 
and so forth by reference to catalogs, specifications, instruction manual, etc. in case that you intend to use azbil product for any purposes 
specified in (1) through (6) below.  Moreover, you are required to provide your Equipment with fool-proof design, fail-safe design, anti-
flame propagation design, fault avoidance, fault tolerance, and other kinds of protection/safety circuit design on your own responsibility 
to ensure reliability and safety, whereby preventing problems caused by failure or nonconformity. 

Terms and Conditions

Содержание PTG71





















































































Отзывы: