manualshive.com logo in svg

Azbil FRS100, Руководство пользователя

Поделиться
Скачать
Azbil FRS100 Скачать руководство пользователя страница 28

18

•  False flame is detected at startup

Chapter 2. MOUNTING AND WIRING

Flame detection

(3)Start contacts OFF

POWER LED

Flame output

Start check completion

FLAME LED

Start check LED

Start contact (term.7-2)

Elapsed time

Start check (2s)

(1)Power ON

(2)Start contacts ON

No

Input status

FRS100 activity

Output activity

1

Power ON

Power is applied across terminals 1 and 2.

(POWER LED lights up)

Flame detection

Relay 2K is turned on by a false flame signal.

(FLAME LED lights up)

2

Start contacts ON

When the start contacts are closed power is applied

across terminals 7 and 2. The start check is carried

out, and relay 1K does not turn on because 

a false flame is detected.

3

Start contacts OFF

Power across terminals 7 and 2 is cut off. The 
FRS100 returns to standby status and waits for 
the next start signal.
If the false flame signal is continuous, the FLAME 
LED is also ON continuously.

Note: It is possible that relay 2K may turn ON when the power is turned on.

Содержание FRS100

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды