Ayrton MagicBlade R, Руководство пользователя

Страница: 13 / 20

USER MANUAL _
13
Timer PIN
The “Timer PIN” is the password required to reset the counter for “Last
Run Hrs.” The PWD is 038.
w Access the menu by pressing the “Mode Esc” key.
w Use the up/down arrow keys to reach the “INFO” menu and press
“Enter.” Then use the left/right arrow keys to select “Time Info.” Finally,
use the left/right arrow keys to select “Timer PIN.”
w Scroll through using the left/right arrows until 038 appears and press
“Enter” to confirm.
CLR LAST RUN
After entering the “Timer PIN”, you can reset the value for “Last Run Hrs”
through this menu.
w
Access the menu by pressing the “Mode Esc” key.
w Use the up/down arrow keys to reach the “INFO” menu and press
“Enter.” Then use the left/right arrow keys to access “Clr Last Run”
submenu.
w Use the left/right arrow keys to select “ON” to validate the reset.
TEMP. INFO
Head Temp.
Shows the current temperature of the fixture head.
w Access the menu by pressing the “Mode Esc” key.
w
Use the up/down arrow keys to reach the “INFO” menu and press
“Enter.” Then use the left/right arrow keys to access the “Temp.Info”
submenu.
w
Press “Enter” once again to display the temperature of the head.
SOFTWARE VER
Displays the software version of the fixture.
w Access the menu by pressing the “Mode Esc” key.
w Use the up/down arrow keys to reach the “INFO” menu and press
“Enter.” Then use the left/right arrow keys to access the “Software ver”
submenu.
w Press “Enter” once again to display the software version.
NETWORK
This menu directly displays the following network information for the
fixture: IP address, subnet mask, and MAC address.
w
Access the menu by pressing the “Mode Esc” key.
w
Use the up/down arrow keys to reach the “INFO” menu and press
“Enter.” Then use the left/right arrow keys to access the “Network”
submenu.
w
Press “Enter” once again to display the information.
TEsT
HOME
Allows you to reset the functions from a DMX controller. You can select
these functions by adjusting the channel.
w
Access the menu by pressing the “Mode Esc” key.
w
Use the up/down arrow keys to reach the “TEST” menu and press
“Enter.” Then use the left/right arrow keys to access the “Home”
submenu.
w
Press “Enter” once again to select “All” or “Pan&Tilt.”
TEST CHANNEL
Tests each of the fixture’s settings (e.g., PAN, TILT).
w Access the menu by pressing the “Mode Esc” key.
w Use the up/down arrow keys to reach the “TEST” menu and press
“Enter.” Then use the left/right arrow keys to access the “Test Channel”
submenu.
w The fixture then runs in test position. Use the left/right arrow keys to
scroll through and test each setting.
MANUAL CTRL.
Allows you to access all the fixture’s settings manually. The shutter and
the electronic dimmer are by default 100% open.
w
Access the menu by pressing the “Mode Esc” key.
w
Use the up/down arrow keys to reach the “TEST” menu and press
“Enter.” Then use the left/right arrow keys to access the “Manual Ctrl”
submenu.
w Use the left/right arrow keys to scroll through and check each setting.
CALIBRATION
Calibrates certain settings such as Pan, Tilt and Zoom. The password
required to access the calibration function is 050.
w Access the menu by pressing the “Mode Esc” key.
w Use the up/down arrow keys to reach the “TEST” menu and press
“Enter.” Then use the left/right arrow keys to access the “Calibration”
submenu.
w
Press “Enter” once again to access the password (050), and press
“Enter” to confirm.
w
Use the left/right arrow keys to move from one setting to another and
press “Enter” to access the calibration function of the setting. Finally,
press “Enter” to confirm the change.
PREsET
SELECT PROG.
Allows to choose the program for “Program Run.”
EDIT PROG.
Allows you to edit internal programs.
EDIT SCENES
Allows you to edit scenes within the internal programs.
SCENES INPUT
The luminaire features a DMX recorder, which can receive the scenes
programmed on your DMX controller. Set the desired number of scenes
from the control panel. Then run the scenes from your controller. They will
be automatically transmitted to the MAGICBLADE-R.
mAStEr/SLAVE modE SEttInGS
A MASTER fixture can send up to 3 different sets of data to a SLAVE
fixture (e.g., a MASTER fixture can control 3 different SLAVE fixtures which
will each perform 3 different programs). The MASTER fixture sends the 3
programs in a continuous loop.
The SLAVE fixture receives data from the MASTER fixture according to the
group to which the SLAVE fixture is assigned. For example, if the SLAVE
fixture has been assigned to “Slave 1” in the menu “Set to Slave”, the
MASTER fixture sends “Auto Program Part 1” to this SLAVE fixture. If it