14
© 2013 Axxiom Manufacturing, Inc.
1.39. NEVER AIM BLAST NOZZLE TOWARDS ANY PERSON.
Do Not aim the blast nozzle towards yourself or any person. System malfunction can cause
accidental start up and result in injury to personnel.
1.40. NEVER USE ABRASIVE NOT INTENDED FOR BLAST EQUIPMENT.
Do Not use abrasive blast media containing free silica. Silica can cause silicosis or other related
respiratory damage. Verify that the abrasive is intended for use in blasting equipment. Personal
protective equipment, including airline filters and respirators, must be used for all abrasive
blasting operations. Observe all applicable local, state and federal safety regulations. See
Section 3.8, 3.10, and reference OSHA 29 CFR 1910.134.
1.41.
CHECK ABRASIVE FOR DEBRIS.
Do Not use blast abrasive that contains trash or other debris. Trash or debris can create a
blockage and cause equipment malfunction. Screen recycled abrasive to remove trash.
1.42. STOP OPERATION IMMEDIATELY IF ANY ABNORMALITY IS DETECTED.
Do Not operate this equipment if anything abnormal is seen during operation. Stop operation
immediately for inspection. See Section 8.0.
1.43. DO NOT OVERLOAD THE LIFT EYES.
Do Not load the lifting eyes above the rated capacity. Do Not lift the blast vessel by any point
other than the lifting eyes or designated lift points. Do Not lift the blast vessel while it is
pressurized. See Section 2.6.
1.44 DO NOT TRANSPORT BLAST EQUIPMENT LOADED WITH ABRASIVE.
Do Not attempt to roll portable blasters with abrasive inside. The additional weight of the
abrasive can cause loss of control of the blaster while moving which can result in injury to
operating personnel.
1.45. MAINTAIN WARNING DECALS.
Do Not remove, cover, obstruct, or paint over any warnings, cautions, or instructional material
attached.
Warning decals must be installed, maintained, and located to be visible and with
enough light for legibility. See Section 0.0 and 8.12.
1.46. SAVE THIS OPERATION AND MAINTENANCE MANUAL.
Refer to this operation and maintenance manual as needed as well as any additional information
included from other manufacturers. Never permit anyone to operate this equipment without
having him/her first read this manual and receive proper training. Make this manual readily
available to all operating and maintenance personnel. If the manual becomes lost or illegible
replace it immediately. This operation and maintenance manual should be read periodically to
maintain the highest skill level; it may prevent a serious accident.
1.47. SAFETY REFERENCES
See Section 12.4 for safety information sources and contact information. Use these sources to
obtain additional information regarding all aspects of blast operation safety.
Содержание SCHMIDT
