background image

 

© 2013 Axxiom Manufacturing, Inc. 

 

WARNING 

1.  Any person intending to operate this equipment or any person intending to be in 

the  vicinity  during  its  operation  must  receive  proper  training  from  his/her 

supervisor, employer and/or supplier. If this equipment is to be leased or rented, 

the supplier must assure that the lessee or renter has received proper training 

before  the  lessee  or  renter  takes  possession  of the  equipment.  Consult  Axxiom 

Manufacturing, Inc. 

 

2.  Any person authorized to operate this equipment or any person intending to be 

in  the  vicinity  during  its  operation  and  who  is  not  capable  of  reading  and 

understanding this manual must be fully trained regarding the 

Rules for Safer 

Operation

  and  all  operating  procedures,  and  must  be  made  aware  of  all  the 

Dangers,  Warnings,  and  Cautions  identified  herein.  Consult  Axxiom 

Manufacturing, Inc. 

 

3.  Do  Not  operate  any  abrasive  blaster  or  blast  equipment  before  reading  and 

completely  understanding  all  the  warnings,  operating  procedures  and 

instructions, and the 

Rules for Safer Operation

 contained in this manual. 

 

4.  Do  Not  operate  any  abrasive  blaster  or  blast  equipment  without  following  the 

Rules for Safer Operation

  and  all  the  operating  procedures  and  instructions. 

Failure to properly use blast equipment could result in serious injury or death.  

 

5.  Do  Not  perform  any  maintenance  on  any  abrasive  blaster  or  blast  equipment 

while  it  is  pressurized.  Always  depressurize  the  abrasive  blaster  vessel  before 

loading abrasive or performing any maintenance. 

 

6.  Do  Not  use  abrasives  containing  free  silica.  Silica  can  cause  silicosis  or  other 

related  respiratory  damage.  All  operators  must  wear  personal  protective 

equipment  for  all  abrasive  blasting  operations.  Observe  all  applicable  local, 

state  and  federal  safety  regulations  in  conjunction  with  airline  filters  and 

respiratory protection. Reference OSHA 29 CFR 1910.134. 

   

7.  Do  Not  enter  areas  during  abrasive  blasting  operations  without  breathing 

protection.  All  personnel  in  the  vicinity  of  abrasive  blasting  operations  should 

wear NIOSH approved air fed respirators, hoods or helmets. 

   

8.  Do Not modify or alter any abrasive blaster, blast equipment or controls thereof 

without written consent from Axxiom Manufacturing, Inc. 

 

9.  Do Not use bleeder type deadman valves on any Schmidt® abrasive blaster. The 

use  of  A-BEC,  Clemco  or  a  similar  bleeder  type  deadman  valve  can  cause 

unintentional  start-up  without  warning,  which  can  result  in  serious  personal 

injury. 

 

10. Do Not sell, rent, or operate abrasive blasters without remote controls. OSHA 

regulations require remote controls on all blast machines. Failure to use remote 

controls can cause serious injury or death to the operator(s) or other personnel 

in the blasting area. Reference OSHA 29 CFR 1910.244(b). 

 

11.  Do  Not  repair  or  replace  any  portion  of  Schmidt®  equipment  using 

components  that  are  not  Schmidt®  original  factory  replacement  parts.  Use  of 

replacement  components  that  are  not  Schmidt®  original  factory  replacement 

parts  may  result  in  equipment  failure  which  can  result  in  serious  personal 

injury and in addition will void all warranties. 

Содержание SCHMIDT





























































Отзывы: