AXMINSTER WORKSHOP 108512 Скачать руководство пользователя страница 26

Страница: 26 / 28

DECLARATION OF CONFORMITY

Axminster Tool Centre Ltd

EC DECLARATION OF CONFORMITY

‘original’

Product model:

Axminster Workshop AW2260S Spiral Planer Thicknesser

Name and address of the manufacturer:

Axminster Tool Centre Ltd, Unit 10 Weycroft Avenue,

Axminster, Devon EX13 5PH, United Kingdom

This declaration of conformity is issued under the sole responsibility of the manufacturer.

Object of the declaration:

Axminster Workshop AW2260S Spiral Planer Thicknesser

The object of the declaration described above is in conformity with the relevant GB legislation:

Supply of Machinery (Safety) Regulations 2008 as amended.
Electromagnetic Compatibility Regulations 2016 as amended

References to the relevant harmonised standards used or references to the other technical
specifications in relation to which conformity is declared

EN ISO 12100:2010 - Safety of Machinery. General principles for design. Risk

assessment and risk reduction.

EN 60204-1:2018 Safety of machinery - Electrical equipment of machines - General

requirements

EN ISO 19085-1:2017 - Woodworking machines - Safety - Part 1 Common

Requirements.

EN ISO 19085-7:2019 - Woodworking machines - Safety - Part 7: Surface

planing, thickness planing, combined surface/thickness planing machines.

EN 60034-1:2010 - Rotating electrical machines - Part 1: Rating and performance

EN 60034-5:2001+A1:2007 - Rotating electrical machines - Part 5: Degrees of protection

provided by the integral design of rotating electrical machines (IP code); Classification

EN 60034-11:2004 - Rotating electrical machines Part 11: Thermal protection

Additional information

Name and address of person authorised to compile the technical file:

Axminster Tool Centre

Ltd, Unit 10 Weycroft Avenue, Axminster, Devon EX13 5PH, United Kingdom

The machinery fulfils all relevant provisions of Supply of Machinery (Safety) Regulations 2008
as amended

Signed for and behalf of

: Axminster Tool Centre Ltd;

(place and date of issue):

Axminster, Devon, United Kingdom Kingdom, 7th July 2022

(name, function):

Andrew Parkhouse, Supply Chain Director

Signature

………………………………………………………………

Содержание 108512





























Результаты поиска

Содержание 108512

Отзывы:

Похожие инструкции для 108512

Бренды по названию

Популярные бренды

AXMINSTER WORKSHOP 108512, Руководство пользователя

Результаты поиска

Содержание 108512

Отзывы:

Похожие инструкции для 108512

Бренды по названию

Популярные бренды