Axel Falcon 35 Скачать руководство пользователя | Manualshive

Страница: 28 / 99

background image

GENERAL DESCRIPTION

ENG

Page 28

14 GENERAL DESCRIPTION

14.1 REAR PANEL VIEW (FM & ST)

FM version

14

15 16

I

I

I

Input

Output

L

R

L

R

Opto

Input

Relay

Output

AUX1-NTW

AUX2-RDS

MPX

Out

MPX

Test

MPX

Out

Digital Input

Serial RS-232

1

3

2

1

3

2

1 3 2

1 3 2

1

3

2

I I

I

I

I

I

I I I I

I

I

1 2

4

5 6 7

8 9

10

11 12

13

ST version

14

I

Input

Output

L

R

L

R

Digital Output

Digital Input

Serial RS-232

1

3

2

1

3

2

1 3 2

1 3 2

1 3 2

1

3

2

I I

I

I

I

I

1 2

3

4

12

13

1 ON/OFF

Switch: main ON/OFF switch, the LED inside switches on/off accordingly. The power supply

socket (use the cord provided) has a built-in fuse drawer containing the power fuse and a spare, both
of the same value: for 230 V AC the fuse is rated at 500 mA T; for 110 V AC it is rated at 630 mA T

2 RS232 Serial Port 2: This port is intended for the processor setting and programming from satellite

and unidirectional links. Supported Baud Rate: 4800.

3 Digital

audio

output*: This has two connectors: use the XLR for balanced coaxial connections and the

tos-link for optical connections. It provides Aes/Ebu and Spdif signals @ 48 KHz, 24 bit.

4 Digital audio input*: This has two connectors: use the XLR for balanced coaxial connections and the

tos-link for optical connections. It accepts Aes/Ebu and Spdif signals at different sampling rates

5 Sync-out*: 19KHz synchronism output at 5Vpp, to lock external equipment (such as RDS coders)

6

SPLIT ON Led*: it lights on while the Split command is active (and thus the OUT 2 is on Split)

7 MPX

OUT

2*: additional MPX output, driven by a special circuit ( ‘SPLIT’).

8 MPX

OUT

1*:

main MPX output. The trimmer near the Bnc connector tunes the MPX output level

between -inf and +12 dbu (factory preset is 0dbu). Accordingly to the current configuration, the output
BNC connector will include the composite / MPX program signal with the RDS / SCA subcarrier mixed
into and with or without signals injected from AUX inputs.

9 MPX OUT 1 TEST*: provides a repetition of the output signal appearing at the main MPX OUT 1

connector, with the same level. It may serve for measurement or as secondary MPX output.

10 AUX 1 Input*: Bnc female connector. Depending on the MPX board configuration, it allow the injection

of RDS/SCA or MPX signals from external encoders/generators. The resultant signal is available on
the Output connectors OUT 1 or OUT 2. Factory preset: 0dB gain.

11 AUX 2 input*: Bnc female connector. Depending on the MPX board configuration, it allow the injection

of RDS/SCA or MPX signals from external encoders/generators. The resultant signal is available on
the Output connectors OUT 1 or OUT 2. Factory preset: 0dB gain.

«
...
26
27
28
29
30
...
»

Содержание Falcon 35




































































































Отзывы:

Нет отзывов

Похожие инструкции для Falcon 35

DS1-MP10RX series

Бренд: NEC Страницы: 39

Бренд: iMode Страницы: 16

Бренд: Sammic Страницы: 28

Бренд: QSC Страницы: 10

Tensioned Cosmopolitan Electrol

Бренд: Da-Lite Страницы: 8

Бренд: KitchenAid Страницы: 516

Бренд: Duronic Страницы: 29

Бренд: AMX Страницы: 2

Бренд: Rotel Страницы: 7

VADDIO RoboTRAK 999-7270-000B

Бренд: LEGRAND Страницы: 4

Бренд: LEGRAND Страницы: 12

Бренд: Girmi Страницы: 32

118-131106 Series

Бренд: Christie Страницы: 3

Бренд: Miranda Страницы: 47

Бренд: Vitek Страницы: 8

Бренд: XTA Страницы: 58

Бренд: TC Electronic Страницы: 16

MultiSync LT245

Бренд: NEC Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды