manualshive.com logo in svg

Axel Falcon 35, Руководство по эксплуатации

Поделиться
Скачать
Axel Falcon 35 Скачать руководство пользователя страница 29

GENERAL DESCRIPTION

            

ENG

  

Page 29 

 
12  ANALOG AUDIO OUTPUT: It provides the L and R processed audio signals on which it is possible to 

enable/disable pre-emphasis. The level is set via menu. 

 

 

13  ANALOG AUDIO INPUT: bi-channel audio input electronically balanced on XLR female. The input 

level is set via menu. An hardware bypass directly connect the two input XLRs to the output ones in the 
event of power failure or processor switched off. 

 

 

14  RS232 SERIAL PORT 1: This port is intended for the processor setting and programming by means of 

the supplied Pc control software application (bidirectional connection). Supported Baud Rate: 19200. 

 

 

15  OPTO INPUT PORT*: SubD 9-pin female Interface. It supports 2 optoinsulated “trigger” inputs (for TA 

flag toggle and for SPLIT mode enabling)  

 

 

16  RELAY OUTPUT*: Reserved for future use 
 

* available as an option 

 
 
 
 

14.2  FRONT PANEL CONTROLS AND SIGNALLINGS 

 
The processor front panel contains 3 red LEDs with the following meaning: 
 
DIGITAL INPUT 

This LED lights up while the DIGITAL Audio input is selected (via front 
panel menu or Pc Software Control). , 

 

 

PREEMPHASIS 

This LED lights up while the Preemphasis (either 50 or 75 uSec) is 
removed from the processed Left and Right output XLR connectors. (NB 
preemphasis can NOT be removed from the MPX outputs). 

 

 

WARNING 

this LED (normally off) lights in the following cases: 
- With ‘Bypass’ or ‘Peak Reference Tone’ modes enabled 
- Internal Temperature exceeding 60 °C.  
- TA (Traffic Announcement) flag enabled (FM /RDS version only) 

 
The processor front panel also contains two buttons, a large display  
 
MULTIFUNCTION DISPLAY  See next Section 
 

 

LCD CONTRAST TRIMMER  it sets the contrast on the multifunction display. The temperature variation 

could effect the contrast, to set it, please use a small screwdriver 

 

 

SHUTTLE KNOB 

It allows to scroll the menu and modify the parameters. To modify any 
parameter you need to turn the shuttle till it will appear on the display (see 
chapter 6). The shuuttle can also be pressed, having the same ENTER 
control function. 

 

 

ENTER KEY 

it gives access to the parameters submenu and selects the new values. 

 

 

ESC KEY 

key to quit the current menu and go back to the previous one. By pressing 
this key the modifications realized by accident on the selected parameter 
are not executed. 

 

Содержание Falcon 35




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды