background image

10

INSTALLATION 

 

          

INSTALLATION INSTRUCTIONS

CAUTION!

Wear gloves to protect against sharp edges.

IMPORTANT! 

PLEASE FOLLOW THESE INSTRUCTIONS 

TO TEST THE RANGE HOOD BEFORE 

INSTALLATION FOR ANY DEFECTS OR 

SHIPPING DAMAGE:

•  Remove the range hood and accessories from 

the package carefully.

•  Place the Hood Unit and the Blower Unit on a 

flat stable surface, remove the baffle filter and 

check for any dent or damage on the range hood 
body.

•  Remove the loosen parts if there's any.
•  Plug the range hood into a 120V AC power 

source. Touch the Speed Selection (-) or (+) 

button to turn it on.

•  Check each speed variation and pay attention 

to the noise level to make sure there isn't any 
unusual noise besides it coming from the wind 
blowing. Press the Light Button to check the 
lights.

• 

Verify all functions, as instructed in Page 12, are 

operational.

•  Refer to Range Hood Troubleshooting in Page 

14 for general issues and solutions.

• 

The white proctive film on the baffle filter must 

be removed before using the range hood.

•  If the range hood you receive is damaged or 

defective, please contact the seller immediately. 

Do not try to install and use the damaged or 
defective unit.

IMPORTANT! 

TO AVOID DAMAGE TO THE RANGE HOOD, DO 

NOT LET DEBRIS ENTER THE VENT OPENING.

CAUTION!

IF MOVING THE COOKING RANGE IS 

NECESSARY TO INSTALL THE RANGE HOOD:

• 

For electric ranges, unplug the power first before moving it.

• 

For gas ranges, shut off the gas valve before moving it.

Observe and prepare the location

•  Determine the location for the range hood. Refer 

to instructions in Page 7 for clearance guidiance.

•  Determine which venting method to use: roof or 

wall.

• 

Purchase any neccessary accessories, such as 
duct, elbow, reducer, damper, duct tape, screws 
etc., from the hardware store.

• 

Use a stub finder to locate and mark the studs 

inside the wall.

• 

Before beginning the installation, make sure 

there is proper clearance within the ceiling or 
wall for the exhaust vent.

Installing the Range Hood

Note

•  The ceiling must be able to hold at least 265 lbs 

of weight.

•  The ceiling must be at least 1-1/4" thick if the 

range hood's top mounting plate is to be installed 
directly to the ceiling.

•  It is recommended to build a stud frame above 

the ceiling and install the range hood to the 
studs for a more secure installation.

The following steps requires 2 or more people:

•  Determind the location and height to mount the 

range hood. The range hood should be aligned 
with the stove.

•  Mark the perimeter of the top of the duct cover 

on the ceiling.

• 

Drill a hole, which is 6-3/4" in diameter, in the 

center of the perimeter in the ceiling for the 6" 
duct access.

•  Align the mounting plate with the perimeter 

and drill 12 holes in the ceiling. Make sure the 
electrical box opening on the mounting plate is 

Содержание RH-WQ Island Mounted Series

















Отзывы: