Avocent AutoView 3050 Скачать руководство пользователя страница 92

Страница: 92 / 102

AutoView 3050/3100/3200 Switch Installer/User Guide

To use History mode:

Press

Ctrl-F9

. The mode will display as History.

Press one of the following key combinations to perform the indicated action:

•

Home

: Move to the top of the buffer.

•

End

: Move to the bottom of the buffer.

•

Page Up

: Move up one buffer page.

•

Page Down

: Move down one buffer page.

•

Up Arrow

: Move up one buffer line.

•

Down Arrow

: Move down one buffer line.

•

Ctrl-F8

: Enters Configuration mode. The Configuration screen will appear.

•

Ctrl-F9

: While in Configuration mode, returns to the previous screen with History

mode enabled.

•

Ctrl-F10

: While in Configuration mode, returns to the previous screen with On-Line

mode enabled.

•

Ctrl-F11

: Clears the history buffer. If you choose this option, a warning screen will appear.

Press

Enter

to delete the history buffer or

Escape

to cancel the action. The previous

screen will reappear.

When finished, press

Ctrl-F10

to exit History mode and return to On-Line mode.

Serial IQ module pinouts

Table B.1 lists the pinouts for the serial IQ module.

Table B.1: Serial IQ Module Pinouts

DB9-F
Pin

Host Signal Name Description Signal Flow

SRL Signal Name Description

DCD - Data Carrier Detect

Out of SRL

DTR - Data Terminal Ready

RXD - Receive Data

Out of SRL

TXD - Transmit Data

In to SRL

RXD - Receive Data

DTR - Data Terminal Ready

In to SRL

DSR - Data Set Ready

GND - Signal Ground

N/A

GND - Signal Ground

DSR - Data Set Ready

Out of SRL

DTR - Data Terminal Ready

RTS - Request to Send

In to SRL

CTS - Clear to Send

Out of SRL

RTS - Request to Send

N/C - Not Connected

N/A

N/C - Not Connected

Содержание AutoView 3050







































































































Результаты поиска

Содержание AutoView 3050

Отзывы:

Avocent AutoView 3050, Инструкция по установке и эксплуатации, Страница: 92 / 102

Результаты поиска

Содержание AutoView 3050

Отзывы: