Avital AviStart 3000 страница 27 Скачать руководство пользователя

Страница: 27 / 40

This system is most commonly found in Ford, Mazda, Chrysler and GM vehicles. The door lock switch or door key

cylinder may contain either one or two resistors. When interfacing with this type of door lock system, two relays

or a DEI 451M must be used.

If one resistor is used in the door lock switch/key cylinder, the wire will pulse (+)12V in one direction and less

than (+)12V when operated in the opposite direction.

If two resistors are used in the factory door lock switch/key cylinder, the switch/key cylinder will read less than

(+)12V in both directions.

To determine the resistor values, the door lock switch/key cylinder must be isolated from the factory door lock

system. For all testing, use a calibrated digital multimeter that is set to ohms.

1. Cut the output wire from the door lock switch/key cylinder in half.

2. Test with the meter from the switch side of the cut door lock switch/key cylinder wire to a reliable constant

(+)12V source. Some good constant (+)12V references are the power input source to the door lock switch/key

cylinder, the ignition switch power wire, or the (+) terminal of the battery.

3. Operate the door lock switch/key cylinder in both directions to determine the resistor values. If the multi-

meter displays zero resistance in one direction, no resistor is needed for that direction.

4. Once the resistor value(s) is determined, refer to the wiring diagram for proper wiring.

determining the proper resistor values

two-resistor type

single-resistor type

type G: positive (+) multiplex

Содержание AviStart 3000









































Результаты поиска

Содержание AviStart 3000

Отзывы:

Похожие инструкции для AviStart 3000

Бренды по названию

Популярные бренды

Avital AviStart 3000, Руководство по установке

Результаты поиска

Содержание AviStart 3000

Отзывы:

Похожие инструкции для AviStart 3000

Бренды по названию

Популярные бренды