Avital AviStart 3000 Скачать руководство пользователя | Manualshive

Страница: 26 / 40

background image

26

© 2001 Directed Electronics, Inc. Vista, CA

Type E door locks are controlled by an electrically activated vacuum pump; however, this DEI system is not

capable of controlling Type E locks.

This system usually requires a negative pulse to unlock, and cutting the wire to lock the door. In some vehicles,

these are reversed. This system is found in late-model Nissan Sentras, some Nissan 240SX, and Nissan 300ZX 1992

and later. It is also found in some Mazda MPV and some Mitsubishi models.

One relay (optional) is used to interface to this type of system as follows:

type F: one-wire system

type E: mercedes-benz and audi (1985 & newer)

«
...
24
25
26
27
28
...
»

Содержание AviStart 3000









































Отзывы:

Нет отзывов

Похожие инструкции для AviStart 3000

Бренд: Bandit Страницы: 3

Бренд: BAMO IER Страницы: 40

Бренд: Caliber Страницы: 17

Бренд: i-PRO Страницы: 8

Бренд: i-PRO Страницы: 4

RoadMate 6000T - Automotive GPS Receiver

Бренд: Magellan Страницы: 119

RoadMate 6000T - Automotive GPS Receiver

Бренд: Magellan Страницы: 119

RoadMate 1400 - Automotive GPS Receiver

Бренд: Magellan Страницы: 81

RoadMate 1212 - Automotive GPS Receiver

Бренд: Magellan Страницы: 62

RoadMate 1212 - Automotive GPS Receiver

Бренд: Magellan Страницы: 60

Magellan Triton 1500

Бренд: Magellan Страницы: 33

Magellan eXplorist 300

Бренд: Magellan Страницы: 88

Magellan eXplorist 300

Бренд: Magellan Страницы: 89

Magellan eXplorist 300

Бренд: Magellan Страницы: 90

Maestro 4350 - Automotive GPS Receiver

Бренд: Magellan Страницы: 23

Бренд: Magellan Страницы: 2

eXplorist - Hiking GPS Receiver

Бренд: Magellan Страницы: 70

Magellan eXplorist 300

Бренд: Magellan Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды