Avital AviStart 3000 Скачать руководство пользователя | Manualshive

Страница: 29 / 40

background image

© 2001 Directed Electronics, Inc. Vista, CA

29

internal programming jumper

NOTE:

The control module door must be removed to access the jumper.

In most cases, this jumper can be left in the OFF position. Some new vehicles use less than 12 volts in their igni-

tion systems. The unit may have trouble learning the tach signal in these vehicles. Changing the jumper to the

ON setting changes the trigger threshold of the digital tach circuit so it will work properly with these vehicles.

The vehicles affected include many newer Dodge/Chrysler/Plymouth vehicles, such as the Neon, Cirrus, Stratus,

Breeze and LH-based vehicles.

digital tach threshold on/off

«
...
27
28
29
30
31
...
»

Содержание AviStart 3000









































Отзывы:

Нет отзывов

Похожие инструкции для AviStart 3000

Бренд: D-Link Страницы: 2

Бренд: 3M Страницы: 2

Бренд: Faraday Страницы: 2

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 2

Digiplex EVO DGP2-640

Бренд: Paradox Страницы: 24

Бренд: Digital Watchdog Страницы: 2

IQeye Sentinel Series

Бренд: Invision Страницы: 20

Бренд: Renkforce Страницы: 8

Бренд: RAB Lighting Страницы: 9

Бренд: Velleman Страницы: 22

Бренд: Audiovox Страницы: 6

NIVD-DIVA-SW13AI

Бренд: Okina USA Страницы: 3

CMD-4000 Series

Бренд: Dakota Digital Страницы: 6

Бренд: Kompernass Страницы: 213

Бренд: Chuango Страницы: 52

Wisenet QNE-8011R

Бренд: Hanwha Techwin Страницы: 15

Бренд: C.P. Electronics Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды