Avital AviStart 3000 Скачать руководство пользователя

Страница: 15 / 40

remote start harness (H2) wire connection guide

This output is programmable. If programmed for status output, the wire will supply a 200 mA ground output at

all times the remote start is operating. If programmed for factory security rearm, the wire will supply a 200 mA

ground pulse whenever the remote start times out or is shut down using the transmitter.

This output provides 200mA as soon as the remote starter is activated. It is used to power a relay to energize a

third ignition or accessory wire as shown below. This output is capable of driving two relays if necessary.

This wire MUST be connected to the hood pinswitch. This input will disable or shut down the remote start when

the hood is opened.

This wire MUST be connected to the vehicle's brake light wire. This is the wire that shows (+) 12V when the brake

pedal is depressed. The remote start will be disabled or shut down any time the brake pedal is depressed.

This input provides the module with information about the engine's revolutions per minute (RPMs). It can be

connected to the negative side of the coil in vehicles with conventional coils. In multi-coil and high energy igni-

tion systems locating a proper signal may be more difficult. (See

Finding the Wires You Need

section of this guide

for finding the tachometer wire.) Once connected, you must teach the system the tach signal. (See

Tach Learning

section of this guide.)

H2/5 VIOLET/WHITE tachometer input

H2/4 BROWN (+) brake switch input

H2/3 GRAY (-) hood pinswitch input

H2/2 BLUE/BLACK (-) optional third ignition output

H2/1 BLUE status/factory security rearm output

Содержание AviStart 3000









































Результаты поиска

Содержание AviStart 3000

Отзывы:

Похожие инструкции для AviStart 3000

Бренды по названию

Популярные бренды

Avital AviStart 3000, Руководство по установке

Результаты поиска

Содержание AviStart 3000

Отзывы:

Похожие инструкции для AviStart 3000

Бренды по названию

Популярные бренды