Avital AviStart 3000 Скачать руководство пользователя

Страница: 8 / 40

How to find a (+) parking light flash wire with your multimeter:

1. Set to DCV or DC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Probe the wire you suspect of being the parking light wire. Usually, the area near the headlight/parking light

switch is an excellent area to start, as is the kick panel.

4. Turn on the parking lights. If your meter shows (+)12V, turn off the parking lights and make sure it goes back

to zero.

5. If it does return to zero, turn the parking lights back on and, using the dash light dimmer control, turn the

brightness of the dash lights up and down. If the meter changes more than a volt when using the dimmer,

look for another wire. If it stays relatively close to (+)12V, you have found your parking light wire.

NOTE:

Vehicles that use a (-) signal from the switch to the factory relay may be interfaced directly.

(See H1/5 WHITE wire of Primary Harness (H1) Wire Connection Guide section.)

To test for a tachometer wire, a multimeter capable of testing AC voltage must be used. The tachometer wire will

show between 1V and 6V AC. In multi-coil ignition systems, the system can learn individual coil wires. Individual

coil wires in a multi-coil ignition system will register lower amounts of AC voltage. Also, if necessary, the system

can use a fuel injector control wire for engine speed sensing. Common locations for a tachometer wire are the

ignition coil itself, the back of the gauges, engine computers, and automatic transmission computers.

IMPORTANT!

Do not test tachometer wires using a test light or logic probe. The vehicle will be

damaged.

How to find a tachometer wire with your multimeter:

1. Set to ACV or AC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Start and run the vehicle.

4. Probe the wire you suspect of being the tachometer wire with the red probe of the meter.

5. If this is the correct wire the meter will read between 1V and 6V.

finding the tachometer wire

Содержание AviStart 3000









































Результаты поиска

Содержание AviStart 3000

Отзывы:

Похожие инструкции для AviStart 3000

Бренды по названию

Популярные бренды

Avital AviStart 3000, Руководство по установке

Результаты поиска

Содержание AviStart 3000

Отзывы:

Похожие инструкции для AviStart 3000

Бренды по названию

Популярные бренды