background image

 

 

9 (36) 

 

 

 

 

DANGER

 

Risk of crushing -  Going under the loader boom or an 
attachment can cause serious injury or death.

  Never go 

under the loader boom and prevent others from getting near 
lifted boom or attachment. Going under a raised attachment 
or loader boom is dangerous, as the boom may lower due to 
loss of stability, mechanical  fault or when other person 
operates the controls of the loader. Lower the attachment 
firmly on the ground to a safe position before leaving the 
driver’s seat. 

Keep in mind that the loader boom can be lowered or tilted 
even if the engine has been shut down  (crushing hazard). 
The loader is not intended to be left to keep a load elevated 
for longer periods. Always lower the attachment to a safe 
position before leaving the driver's seat. 

 

 

 

.. 

 

 

 

 

DANGER

 

Risk of crushing and severing of limbs- Always stop the attachment before going 
near it.

  Going near a running attachment creates a risk of crushing and severing of 

hands or feet because of moving spreader plate and related components. Always follow 
safe stopping procedure. 

 

 

 

 

 

WARNING

 

Risk of thrown objects and dust - Use the Silage Dispenser only for its intended 
purpose. 

Using the attachment for other purposes than handling and dispensing cattle 

feeding materials can cause hazardous ejection of material, dust, or damaged machine 
parts. Use only to dispense materials that are commonly used as feeding materials. 
Consult your Avant dealer if necessary. 

 

 

 

 

 

WARNING

 

Choking hazard - Ensure ventilation when using a loader with combustion engine 
indoors.

  Using the loader engine indoors increases, among other things, the carbon 

dioxide level of the air, which affects the safety of the operator. Make sure that ventilation 
is sufficient and adapt use periods according to operating conditions. 

 

 

 

 

 

WARNING

 

Entanglement and severing hazard -  Never go near a broom that is running.

  The 

powerful broom can cause serious injuries to anyone too close to it. Always stop the 
attachment following the safe stopping procedure before going near the attachment. If 
being near a running attachment is absolutely necessary during specific maintenance or 
fault finding operation, never wear loose clothing, long scarves, jewellery, or other items 
that might become entangled with rotating parts while operating the attachment. If 
needed, wear a hat to prevent long hair from coming into contact with the rotating parts. 
Before maintenance and service stop the broom following the safe stopping procedure.  

 

Содержание A424013





































Отзывы: