background image

For product information and a complete list of distributors, please go to our web site:         

www.avagotech.com

Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change.  Copyright © 2005-2008 Avago Technologies. All rights reserved.  Obsoletes AV01-0480EN
AV02-1405EN - September 9, 2008

Appendix F: Kit Components

The designer’s kit contains components as follows:

Part Number

Description

Name

Quantity

ADNS-6010

Laser Mouse Sensor

Sensor

5

ADNS-6120

Laser Mouse Round Lens Plate 

Lens

5

ADNS-6130-001 

Laser VCSEL Trim Lens Plate

Lens

5

ADNS-6230-001

Laser VCSEL Assembly Clip

VCSEL Clip

5

ADNV-6340

Single Mode Vertical Cavity Surface Emitting LASER (VCSEL)

VCSEL 

5

ADNK-6013-SP01
CD

Includes Documentation and Support Files for ADNK-6013-SP01

    Documentation 
         a.   ADNS-6010 Data Sheet
         b.   ADNS-6120 Round Lens Data Sheet
         c.   ADNS-6130-001 Trim Lens Data Sheet
         d.   ADNS-6230-001 VCSEL Assembly Clip Data Sheet
         e.   ADNV-6340 VCSEL Data Sheet
         f.    Avago Technologies ADNS-6000, ADNS-6010, ADNS-6090 and ADNS-7010
               Laser Mouse Sensor Eye Safety Calculations Application Note 5088

    Hardware Support Files
        a.   ADNK-6013-SP01 BOM List
        b.   ADNK-6013-SP01 Schematic 
        c.   3D Model IGES Files
        d.   Gerber File

    Software Support Files

        a.   Microcontroller Firmware

1

Содержание ADNK-6013-SP01
















Отзывы: