manualshive.com logo in svg

Autometers Systems HORIZON HT-1095, Руководство пользователя, Страница: 3 / 28

Поделиться
Скачать
Autometers Systems HORIZON HT-1095 Скачать руководство пользователя страница 3

Introduction

The HT-1095 is a multifunction energy 

analyzer and is the latest in a new 

generation of MID approved intelligent 

panel meters used not only in the 

electricity transmission and power 

distribution system, but also in the 

power consumption measurement and 

analysis in high voltage intelligent power 

grid.

The HT-1095 is capable of measuring 

electricity in one phase two wire, three 

phase three wire or three phase four 

wire electrical systems.

The meter is a 96 x 96mm panel 

mounted meter designed to be easy to 

use and easy to read, the meter comes 

with five control buttons for scrolling 

and programming with a large back light 

display for ease of reading. See picture 

opposite.

The meter displays the following 

information: Voltage, Frequency, 

Current, Power active and reactive 

energy, imported or exported, Power 

factor, Max. Demand and Harmonics 

distortion measurement on current and 

voltage to the 63rd.

Energy is measured in terms of kWh, 

kVArh. Maximum demand current can 

be measured over preset periods of up 

to 60minutes. In order to measure 

energy the unit requires voltage and 

current inputs. 

The HT-1095 is a 1 amp or 5 amp current 

operating measuring device and can 

only work with current transformers. 

Due to the design of the HT-1095 it is 

fully programmable via the front keys to 

enable a wide range of settings to match 

any current transformer manufactured.

The Information Centre can be supplied 

with a pulse Output or Autometers RS 

485 Modbus protocol v.6.

 Configuration is password protected. 

This document provides operating, 

maintenance and installation 

instructions for the Autometers HT-1095.

www.autometers.co.uk

1

Содержание HORIZON HT-1095





























Отзывы:

Нет отзывов