background image

GDO-11 Ero Installation Manual

4

1. Home Owner Safety Warnings!

This automatic garage door opener is designed and tested to offer safe service provided it is installed and operated 

in strict accordance with the following safety warnings. Failure to comply with the following instructions may result in 

death, serious personal injury or property damage.

WARNING! IMPORTANT SAFETY INSTRUCTIONS 

IT IS IMPORTANT FOR THE SAFETY OF PERSONS TO FOLLOW ALL INSTRUCTIONS.  

SAVE THESE INSTRUCTIONS

 

WARNING!

• 

Details on how to use manual release. When operating the manual release while the door is open, 

the door may fall rapidly due to weak or broken springs, or due to being improperly balanced. 

• 

DO NOT

 disengage the opener to manual operation with children/persons or any objects 

including motor vehicles within the doorway.

• 

If the door is closing and does not re-open when obstructed, discontinue use. 

DO NOT

 use a 

door with faulty obstruction sensing.

• 

Frequently examine the installation, in particular check cables, springs and mountings for signs 

of wear, damage or imbalance. 

DO NOT

 use if repair or adjustment is needed since fault in the 

installation or an incorrectly balanced door may cause injury.

ELECTROCUTION!

• 

Place opener in protected area so that it does not get wet.

• 

DO NOT

 spray with water .

• 

DO NOT

 open the protective covers.

• 

DO NOT 

operate opener if cable is damaged. It must be replaced by the manufacturer, its service 

agent or similarly qualified person in order to avoid a hazard.

• 

Disconnect the supply(s) when cleaning or other maintenance is being carried out.

DO NOT DO IT  

YOURSELF

•    

Keep the garage door balanced. Sticking or binding doors must be repaired. Garage doors, door 

springs, brackets and their hardware are under extreme tension and can cause serious personal 

injury. 

DO NOT

 attempt any garage door adjustment. 

DO NOT

 use if repair or adjustment is 

needed. Call for a professional garage door service.

 BATTERY 

 WARNING!

•    This product contains a lithium button/coin cell battery in the transmitters. If a new or used lithium 

button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and 

can lead to death in as little as 2 hours. Always completely secure the battery compartment. If 

the battery compartment does not close securely, stop using the product, remove the battery and 

keep it away from children. If you think batteries might have been swallowed or placed inside any 

part of the body, 

SEEK IMMEDIATE MEDICAL ATTENTION.

 CAUTION:

 

Emergency access

• 

If your garage has no pedestrian entrance door, an emergency access device should  be installed. 

This accessory allows manual operation of the garage door from outside in case of power failure.

Entrapment under  

operating door  

• 

Watch the moving door and keep people away until the door is completely opened or closed. 

DO NOT

 operate door when persons are near the door.

• 

DO NOT

 allow children to play with door controls or transmitters. Keep remote controls away 

form children.

• 

The appliance is not to be used by persons (including children) with reduced physical, sensory or 

mental capabilities, or lack of experience and knowledge, unless they have been given supervision 

or instruction.

• 

Children being supervised not to play with the appliance.

• 

Regularly conduct Open and Close cycle testing.

• 

Each month check that the drive reverses when the door contacts a 40mm high object placed on 

the floor. Adjust if necessary and recheck since an incorrect adjustment may present a hazard.

• 

Ensure the garage door is in good working order by undertaking regular servicing.

• 

Wall transmitters should be installed in a location where the garage door is visible, but out of the 

reach of children at a height of at least 1.5m.

• 

Install Safety Beams (recommended).

Fall from Ladder

• 

Ensure ladder is the correct type for the job.

• 

Ensure ladder is on flat ground.

• 

Ensure user has 3 points of contact while on ladder.

Entanglement in or 

laceration from  

moving door

• 

Keep hands and loose clothing clear of door and guides at all times.

• 

Keep hands clear of moving door as sharp edges can cause cuts or lacerations.

DIY

Содержание GDO-11 Ero
























Отзывы: