background image

GDO-11 Ero Installation Manual

22

21. After Installation Care

Warranty conditional on proper servicing as listed in 21.1 Service Checklist. Full details of the warranty are available in your 

Owners Opener Handbook, from your nearest ATA office or visit the ATA Website 

ata-aust.com.au

21.4 Warranty

When batteries reach the end of their usual life in accordance with Australian Battery Recycling Initiative please follow the next 

simple steps for protecting the environment. Refer to the Automatic Technology website for information on where to recycle 

batteries in Australia. 

DO NOT throw the batteries in municipal waste. This symbol of the crossed out wheeled bin 

indicates that the battery should not be placed in the municipal waste. Check your local regulations 

for appropriate disposal of the batteries.

Recycling all batteries will have other environmental and social benefits:

WARNING! Prior to disposal, recycling, or collection, all battery terminals must be securely 

insulated with a non conductive material to prevent any two batteries from short circuiting 

and generating heat during storage or transport. Battery terminals may be insulated with 

electrical tape; or batteries may be individually packaged in a non conductive material 

 

(e.g., plastic bag or original packaging).

21.3 Battery Disposal

 

Some batteries are less toxic but hazardous for other reasons. 

Lithium batteries can explode or catch fire in landfill, while button 

cells are dangerous if swallowed by children. Recycling offers a 

safe and environmentally responsible solution for end of life 

batteries.

 

Battery recycling recovers non-renewable materials such as lead, 

cadmium, stella, zinc, manganese, cobalt, silver, plastics and rare 

earth elements.

 

Removal of batteries and other hazardous household products 

from household waste facilitates the recovery of organic materials 

through alternative waste technologies such as composting. 

Batteries and heavy metals are known contaminants in compost.

 

The community supports recycling because it reduces waste to 

landfill and achieves environmental benefits.

WARNING

! The Battery shall be disposed of properly, including keeping them away from children. 

Even used batteries may cause injury.

21.2 Battery Replacement

 

Light Status

Battery 

Solid

OK

Flashing

Replace

No light

Replace

 

3 . 0   C O D I N G   A   R E M O T E   C O N T R O L

S T E P   O N E

The opener can only be operated from remote 

controllers that have been programmed into its 

memory. Up to 64 remotes can be programmed.

Battery Type: 1 x CR2032.

W A R N I N G ! :   The battery is hazardous and must 

be kept out of reach of children. The battery can 

cause severe or fatal injuries within 2 hours or 

less if swallowed or placed inside any part of the 

body. If you suspect the battery has been 

swallowed or placed inside any part of the body, 

SEEK IMMEDIATE medical attention.

S T E P   T W O

S T E P   T H R E E

Switch power on and 

remove controls cover

till remote 

LED lit

Press

repeatedly

HOLD

Opener 

flashes & 

beeps

HOLD for 3 sec

HOLD for 3 sec

RELEASE

Release both 

buttons

S T E P   F O U R

S T E P   F I V E

Press to test

tip

S T E P   O N E

4 . 0   C H A N G I N G   A   B A T T E R Y

HOLD

Check Light 

Status Table

S T E P   T W O

tip

Use screwdriver 

to remove 

screws and 

open

 

S T E P   T H R E E

Use non-metallic 

object to push 

out.

C O D I N G   R E M O T E   F R O M   T H E   O P E N E R

S T E P   O N E

S T E P   T W O

Take a pre-coded 

remote and press the 

button to duplicate

R E M O T E L Y   C O D I N G   A   R E M O T E   C O N T R O L

Remotely coding works when you have a 

pre-coded remote control and are in range of the 

opener.

tip

Use a pen,

HOLD for 2 sec

the middle button 

through the 

coding hole

S T E P   T H R E E

Opener flashes & beeps

HOLD for 3 sec

HOLD for 3 sec

RELEASE

Take new 

remote

RELEASE

S T E P   F I V E

Press to test

Opener stops flashing & 

beeping

Then refit controls cover

WARNING

! The battery is hazardous and must 

be kept out of reach of children. The battery can 

cause severe of fatal injuries within 2 hours or less 

if swallowed or placed inside any part of the body. 

If you suspect the battery has been swallowed or 

placed inside any part of the body, SEEK IMMEDIATE 

medical attention.

Содержание GDO-11 Ero
























Отзывы: