Automated Logic S6104 страница 1 Скачать руководство пользователя

Страница: 1 / 16

Automated Logic Corporation

•

1150 Roberts Blvd.

•

Kennesaw, GA 30144

•

770/429-3000

•

770/429-3001 Fax

•

www.automatedlogic.com

•

Automated Logic logo, SuperVision, Eikon, Alert, InterOp, and WebCTRL are registered trademarks of Automated Logic
Corporation. BACnet

is a registered trademark of ASHRAE. All other brand and product names are trademarked by

their respective companies.

Technical Instructions

S6104

Using the S6104 2
Specifications 3
Mounting 3
Addressing 3
Power Wiring 4
Network Communications 4

Using the S6104 on an ARC156 Segment 5
Using the S6104 on a Legacy CMnet 5
Connecting the S6104 to the Network 5

Communicating with the Workstation Using SuperVision 6

Communicating Through the LogiStat Port Using SuperVision 6
Communicating Through the Access Port Using SuperVision 7

Inputs 8

LogiStat Wiring 10

Digital Outputs 11
Analog Outputs 12
Writing GFBs for the S6104 12
Point Identifiers 13

Point Identifiers in WebCTRL 13
Channel Numbers in SuperVision 13

Transferring Memory 14

Transferring Memory in WebCTRL 14
Transferring Memory in SuperVision 15

Troubleshooting 15

Formatting the Module 15
LEDs 15
Protection 16
Production Date 16

Содержание S6104

















Результаты поиска

Содержание S6104

Отзывы:

Похожие инструкции для S6104

Бренды по названию

Популярные бренды

Automated Logic S6104, Технические инструкции

Результаты поиска

Содержание S6104

Отзывы:

Похожие инструкции для S6104

Бренды по названию

Популярные бренды