Automated Logic S6104 Скачать руководство пользователя страница 7

Revised 7/30/02 • S6104

7

© 2002 Automated Logic Corporation

3. Set the Port Select jumper for LogiStat to 

enable communications through the 
LogiStat Port.    

4. In SuperVision, define the connection 

using Table 3 on page 8.

5. In SuperVision, set the baud rate at 

1200 bps.

6. Attach the LogiStat Adaptor Cable (part 

number 235022) to the APT cable. Use this 
assembly to connect the APT’s Access 
Port to the LogiStat’s LogiPort.

While connected, the LogiStat Pro 
displays “LP” indicating that the LogiStat 
Pro will not respond to input from the 
keypad.

NOTE

When the LogiStat Adaptor Cable 

is inserted into the LogiPort, the S6104 
can no longer read the LogiStat Inputs. 
The S6104 will continue to use the last 
valid temperature and setpoint adjust 
readings obtained before the cable was 
inserted into the LogiPort. If the 
Occupancy Override Timer was active 
when the connection was made, it will 
continue to count down, but no new 
inputs can be made until the LogiStat 
Adaptor Cable is removed. See the 

Eikon 

Microblock Reference Guide

 for more 

information about the LogiStat 
microblock.

7. Disconnect the LogiStat Adaptor Cable 

from the LogiStat's LogiPort when 
finished to allow the S6104 to receive 
inputs from the LogiStat.

Communicating Through the Access 
Port Using SuperVision

When using SuperVision, you can connect a 
workstation or portable computer directly to 
the S6104 module using an APT and the 
module’s Access Port (see Figure 6). This type 
of connection can be used to troubleshoot the 
module or transfer memory. If you are using 
an ARC156 CMnet, you can receive colors 
while connected to a module’s Access Port if 
a gateway module is on the CMnet. You 
cannot receive alarms through the Access 
Port, however.     

1. Connect the computer’s serial port to the 

APT’s EIA-232 port using a standard 
straight-through cable.

2. Set the APT’s Mode Select switch.

• On an ARC156 network segment, use 

the TTL setting.

• On a legacy CMnet, use the 485 setting.

3. Connect the APT’s Access Port to the 

module’s Access Port.

4. Set the Port Select jumper to Access to 

enable communications through the 
Access Port.

 Figure 5. Port Select to LogiStat

Logi-

Access

Stat

Legacy

Port Select

ARC156

Access Port

LogiStat Port

Temp LS5v

Gnd

Sw

Logi-

Stat

Access

 Figure 6. Using the Access Port

EIA-232

Port

9

R x

6 1

2- T x o ut
3 - R x i n
5- G nd
1,6, 8- + 10V or fl oating

T x

+ 5V

APT

5

Ex ec. 4 relay

Isolate

N etw or k

M ode S elec t

T T L

485

A C C E S S

P O R T

Mode Select Switch

Exec. 4 Relay

Switch

Access Port

CONTROL MODULE

Access

Port

Содержание S6104

















Отзывы: