AutoAnchor AA570 Скачать руководство пользователя страница 41

Страница: 41 / 44

Access the information from the Set up menu or from the installation warning screen.

Diagnostic messages help find an installation problem. The diagnostic messages are all

caused by external wiring, set up or installation issues which need fixing. They are not

caused by a fault with the AutoAnchor.

INTERNAL VOLTMETER/TEST TOOL:

This tool displays the voltages and status of

sensor, battery and load wires. The information is required by the AutoAnchor support

team for effective technical assistance.

Contact AutoAnchor support on:

www.autoanchor.co.nz/autoanchor-installation-help

Fill in the information form.

Email: [email protected] or Telephone: +64 9 360 300.

Press

again for extended diagnostic information and test tools.

PART 7 TECHNICIAN dIAGNOSTIC INFORMATION

Use

to scroll through the menus and to

Hold together to display the Set up menu.

The

must be turned off to access the Set up menu

Correct Parameters

AA Grey Sensor

Chain Only

Set Up

Bottom Fit Magnet

Polarity not relevant

Signal A -

(Red sensor wire from the console) is sensor power supply. Voltage

must be between 4.6V and 4.9V.

Signal B -

Reading depends on gap and magnet polarity.

Range 0.5V - 4.6V. Minimum working signal 0.5V.

Signal C -

f Signal B is less than 0.5V then Signal C will take over and

operate down to 100

for an all chain set up.

AA Grey Sensor

Rope/Chain Set Up

Top Fit Magnet

Polarity not relevant

Signal A -

(Red sensor wire from the console) is sensor power supply.

Signal B -

Reading

is not relevant.

Signal C -

Minimum value is 100 mV when reading the chain pulses.

AA Black Sensor

Chain Only Set Up

Bottom Fit Magnet

South pole must face

sensor

Signal A -

(Red sensor wire from the console) moves between 2.6V and 4.6V.

Minimum working signal 0.5V.

Signal B -

Reading is not relevant

Signal C -

Reading is not relevant.

Reed Switch

Chain Only Set Up

Bottom Fit Magnet

Polarity not relevant

Signal A -

(Red sensor wire from the console) is not used.

Black sensor wire (from the console) is connected to the reed switch.

Signal B -

Range is 0.0V to 5V.

Signal C -

Reading is not relevant.

NPN Proximity

Sensor Chain Only

Set Up

Signal A -

(Red sensor wire from the console) is the proximity sensor’s power

supply.

Signal B -

Range 2.5V - 4.6V. Minimum working signal 0.5V

Signal C -

Reading is not relevant.

Sensor

Source

Icon

Signal

Voltage

(V)

Signal (mV)

To update the recorded signal levels rotate the windlass 2 or more turns

Press buttons or freewheel the windlass to rotate.

Check the windlass is safe and clear before using this function.

Sensor Information

Tuning done
Signal A 4.6 0.0
Signal B 2.5 0.5
Signal C -166 501

Sensor

Tuning done
Signal A 4.6 1.2
Signal B 5.0 0.0
Signal C -166 501

Sensor

Tuning done
Signal A 5.0 0.0
Signal B 0.0 5.0
Signal C -166 501

Sensor

Tuning done
Signal A 4.3 0.0

Signal C -166 501

Sensor

Tuning done
Signal A 4.6 0.0
Signal B 2.5 0.5
Signal C -166 501

Sensor

Tuning done
Signal A 4.6 0.0
Signal B 2.5 0.5
Signal C -166 501

Sensor

Signal B 0.5 3.5

3.5

2.2

select windlass. Scroll to

Diagnostics

and select with

Содержание AA570













































Результаты поиска

Содержание AA570

Отзывы:

Похожие инструкции для AA570

Бренды по названию

Популярные бренды

AutoAnchor AA570, Руководство пользователя

Результаты поиска

Содержание AA570

Отзывы:

Похожие инструкции для AA570

Бренды по названию

Популярные бренды