AutoAnchor AA570 Скачать руководство пользователя страница 12

Страница: 12 / 44

Before starting check with the AutoAnchor manufacturer, or supplier, that it is

possible to fit the sensor and magnet to your horizontal windlass.

For an accurate rope count the rode must run between the sensor and magnet. On a

horizontal windlass the magnet and sensor must be fitted by the windlass manufacturer

If it is not possible to have the sensor and magnet fitted to achieve this you can use the

chain only horizontal windlass installation above.

This provides an accurate count of rode

deployed but during retrieval the display may be incorrect because it cannot allow for

the stretch in the rope.

2.1.10 INSTALLATION ON A HORIZONTAL WINdLASS - ROPE & CHAIN

2.1.11 INSTALLATION ON dRUM WINCHES

For drum Winch Set Up and Operation Refer to Page

Gap Between the Sensor and Magnet:

Minimum 5mm and maximum 40mm

The magnet and sensor must be fitted so that the gap remains consistent as the

winch turns
Magnet Installation:

Size: 10mm x 8mm magnet (#9061)

The magnet can be mounted on the main shaft or on the side of the drum. See Figs 8 and

9. If mounted on the side of the drum, position it close to the inside to reduce the

peripheral speed of the magnet. Fix the magnet into position with epoxy ensuring it is

completely sealed to prevent corrosion.

Sensor Installation

The Grey 3 wire AA sensor (#9067) is recommended but a proximity sensor may be used.

Every installation is different so this manual can provide guidelines only. The AA sensor

holder #9070, or a customised sensor holder will be required to ensure the sensor remains

in position and the gap is consistent between the sensor and magnet during operation.

Fig 8

Sensor

Sensor Connection:

The AutoAnchor plug and play sensor extension cable must be

used to connect the sensor to the AA702 base station. Ensure the connectors are firmly

screwed together.

Loose cable should be tied in place with cable ties and kept clear of chain.

Magnet on

side of drum

Magnet

on shaft

Sensor

Fig 9

Magnet

Sensor

Fig 7

Содержание AA570













































Результаты поиска

Содержание AA570

Отзывы:

Похожие инструкции для AA570

Бренды по названию

Популярные бренды

AutoAnchor AA570, Руководство пользователя

Результаты поиска

Содержание AA570

Отзывы:

Похожие инструкции для AA570

Бренды по названию

Популярные бренды