9-17
FITTED EQUIPMENT
every change made to the settings, hence
the system will start up on each subsequent
occasion in the last selected setting.
Switching on
Refer to page 9-18 for illustration of the
control panel.
A
= Main switch (on/off). Press, and the
function LED will turn blue. The LCD
display will show the most recent settings
for 10 seconds and then backlight will go
out.
B
= Mode selection switch. Press, and the
LCD display will show the setting, for 10
seconds. Pressing the switch successive
times moves through the menu in the
following sequence:
• AUTO
• Manual DC (12V)
• Manual gas
• Manual mains voltage (230V)
• AUTO
Select either the AUTO option or one of
the other power supplies you wish to use,
as shown on the LCD display. Ten
seconds after releasing the switch the
backlight will go out.
C
= Cooling level selection switch. Press,
and the LCD display will show the
setting, for 10 seconds. Pressing the
switch successive times will set the
refrigerator one position cooler. On
reaching the coldest temperature the
system will start again at the warmest
setting. Ten seconds after releasing the
switch the backlight will go out.
D
= Function LED
E
= LCD display
•
Open the valve of the gas bottle
•
Open the isolator taps
•
Press the main switch (A). The function
LED will turn blue and all symbols on the
LCD display will light up.
•
Use the mode selection switch (B) to
select the AUTO function (or one of the
power sources you want). The LCD
display will show the selected option.
•
Set the desired cooling level by means of
the selection switch (C). The LCD display
will show the selected option.
Powering with electricity
Powering with electricity can be selected by
the AUTO mode or manually.
•
AUTO mode, mains voltage (230V): This
energy source will be selected if the
mains voltage is greater than 200V.
•
AUTO mode, direct current (12V): This
energy source will be selected only if
mains voltage (230V) is unavailable, the
vehicle engine is running and a voltage
higher than 11V is available.
•
Manual selection, mains voltage (230V):
The LED warns you whenever insufficient
voltage is available or if a fault occurs. If
this happens the LED will flash and the
LCD show an error code.
•
Manual selection, direct current (12V):
Powering from the battery is only suitable
for maintaining the temperature of the
refrigerator and its contents once it has
been refrigerated. Always use the gas
connection or mains voltage to start up
the refrigerator and cool it. The LED
warns you whenever the engine is not
running, if insufficient voltage is available
or if a fault occurs. If this happens the
LED will flash and the LCD show an error
code.
Note:
If the refrigerator has been
manually set to operate on 12V, it will not
automatically switch to another energy
source when the engine is not running. In
this case the refrigerator will stop cooling.
Powering with gas
Powering with gas can be selected by the
AUTO mode or manually.
•
AUTO mode: The system will select gas
operation if mains voltage (230V) is
unavailable or the vehicle engine is not
running. Once either of these is available
again the system will switch to the
highest priority energy source.
Note:
if
the system switches from 12V DC to gas
operation while in AUTO mode, it will wait
for about 15 minutes before igniting the
gas, although the gas indicator lamp will
Содержание Peugeot Kemerton
