background image

 

 

© Austria Email AG 

 

 

29 

V1.0  1/2021 

 

Important:

 the overheating is carried out with the heat source determined by the selected 

operational program, e.g. P1 

 compressor, P2 

 boiler).  

Note:

 in case the overheating is not carried out within 12 hours, the function is switched off and 

normal operation is switched on.  

4. Fast water heating: 

Program P5 provides the function of fast (simultaneous) water heating, where 

both heat sources are operated (heat pump and electric heating element in P5 programme). This 

function is performed by pressing and holding the 

 key for 20 seconds. The light indicator on 

the HT key flashes until the set water temperature is reached. The function can be interrupted by 
pressing the HT key again.  

 
Modes of operation 
 
1.

 

Water heating with the compressor only (P5): 

the water is heated with the compressor, until 

the set temperature is reached or until the temperature of the inlet air remains above the min. 
operational temperature. When the temperature of the water in the water tank drops for 5

°

C, the 

compressor starts the heating process again. If the ambient air temperature falls below the selected 
value, the compressor switches off for about 30 minutes for safety reasons or until a higher ambient 
temperature is achieved. The heating of water is carried out in the P5 program by means of a 
compressor.  
 

2.

 

Water heating with the electric heater (P3):

  the water is heated by means of the electric 

heater until the set water temperature is reached. The active and safety thermostat of the electric 
element is limited to 65

°

C. Because the temperature sensor is installed under the electric heating 

element, the temperature shown on the display can deviate from the actual set temperature.    
 

3.

 

Water heating with an active PV signal (P6):

 The heat pump is heating water to the set 

temperature with the compressor (automatic mode of operation). The operation of the heat pump 
depends on the air temperature.

 

In P6 programme the PV (photovoltaic) signal is also active, which 

means that the water is heated to a higher temperature (the set tempe value set in 
parameter L6 up to max. 65

°

C). This mode of operation is only active if the PV signal is also active. 

 

4.

 

Bivalent operation: 

When the heat pump is in bivalent operation, the water is additionally 

heated with an electric heater. The bivalent temperature is b5

°

C and -5

°

C (parameter L1). 

 
Parameter display and setting 

We enter the parameter menu by shortly pressing the 

 and 

 key simultaneously. For 

browsing through the menu we use one of the keys individually.  
8 seconds after the desired parameter has been selected, the value of the selected parameter is 
displayed for 10 seconds. After that the display reverts to the main menu and shows the current 
water temperature in the storage tank.  
 

Parameter 

Description 

Range 

Default settings 

L0 

Evaporation temperature in 
°C 

-15 

÷

 95 °C 

-  

L1 

Bivalent temperature in °C 

-15°C 

 30°C  

-12  

L2 

Overheating time interval 
in days 

  99 days 

14 

L3 

Customer service 

-  

-  

L4 

Switch-off temperature  
(hysteresis) 
 

1

°

C to 20

°

C  

5

°

C  

Содержание WPA 233 E-LF




































Отзывы: