Aussie Bonza Deluxe Series Скачать руководство пользователя

Страница: 1 / 35

Aussie

LP Gas/
Charcoal Grill

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, immediately call your

gas supplier or your fire department.

FOR YOUR SAFETY

1. Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

2. An LP cylinder not connected for use shall not

be stored in the vicinity of this or any other

appliance.

•READ AND FOLLOW INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY OR USE. FAILURE TO

FOLLOW THESE INSTRUCTIONS COULD RESULT IN DEATH, SERIOUS BODILY INJURY AND/OR

PROPERTY LOSS.

•FOR HOUSEHOLD OUTDOOR USE ONLY. NOT FOR COMMERCIAL USE.

•SOME PARTS MAY CONTAIN SHARP EDGES-ESPECIALLY WHERE NOTED IN THIS MANUAL!

WEAR PROTECTIVE GLOVES IF NECESSARY

•PORCELAIN COATING CAN CHIP DURING ASSEMBLY. WEAR SAFETY GLASSES WHILE

ASSEMBLING GRILL.

•THESE INSTRUCTIONS MUST BE KEPT WITH THE CONSUMER AND RETAINED FOR FUTURE USE.

For Customer Service, call 1-800-251-7558

Bonza Deluxe Series

Bonza Series

Содержание Bonza Deluxe Series




































Результаты поиска

Содержание Bonza Deluxe Series

Отзывы:

Похожие инструкции для Bonza Deluxe Series

Бренды по названию

Популярные бренды

Aussie Bonza Deluxe Series, Руководство пользователя

Результаты поиска

Содержание Bonza Deluxe Series

Отзывы:

Похожие инструкции для Bonza Deluxe Series

Бренды по названию

Популярные бренды