background image

· Always perform a leak test before each use.

· Leak test must be performed in a well ventilated 

  area. 

· Never perform a leak test on a grill while in use or 

  hot.

· If you detect a gas leak that cannot be corrected 

  by using the leak test procedures below, do not 

  use the LP gas grill. 

· Never smoke or have an open flame near the grill 

  during a leak test.

Supplies Needed for a Leak Test

Clean paint brush, water, and dishwashing liquid.

How to perform a leak test (See Step 13 of Assembly 

Instructions for leak test diagrams.)

WARNING! Never use an open flame to test for gas 

leaks.

1) Mix one cup of water with one cup of 

dishwashing          liquid. 

2) Confirm that all control knobs on the control panel 

are     in the “off” position.

3) Remove control knobs and the three retaining 

screws     at the bottom of the control panel.

4) Remove front control panel cover.

5) Open the valve on LP gas cylinder (Turn the 

handle     on the LP gas cylinder counter-clockwise)

6) Check for leaks by brushing the soap solution on 

all     LP gas connections and fittings.  (See STEP 

13 of     Assembly Instructions for diagram of the 7 

locations)      Make sure you generously brush the loca-

tions with the     soap solution, completely surrounding 

the connections     and fittings.           

7) If “growing” bubbles appear on any of the 

connection     points, then you have detected a gas 

leak.     Immediately close the LP cylinder valve by turn-

ing the     handle clockwise.  

    A) If leak appears at either end of hose and regulator 

        assembly, retighten the connection at the leak, 

but          do not overtighten. (Note: Only hand tighten at 

         coupling nut) (See Step 12 of Assembly          Instru

ctions).  Repeat Leak Test. 

    

B) If  the leak is coming from the LP gas 

cylinder,           from the valves at the control knobs, or if 

the leak              cannot be stopped, do not use the grill. 

Call          Customer Service at 1-800-251-7558.

8) Always turn off LP cylinder valve after performing 

a     leak test. (Turn handle clockwise)

9) If your LP gas grill has been in storage or has 

not     been used  for a period of time, the burners should 

be 
    maintained.  See Burner Maintenance in the Care

 

and 

    Maintenance section of  this manual.

 

·  Before proceeding, make certain that you 

    understand the Important Safeguards on pages 2 

    thru 4 of this manual.

 ·  Before lighting the LP gas grill, you must open 

    the hood to prevent an explosion from gas build-up.    

                                                                        · If your LP 

gas grill catches on fire:

     - If the fire is in the grill portion and you can safely 

       reach the control knobs on the control panel, then 

       turn them to the off position.

     - If the fire involves one of the hoses, and you can 

       safely reach the LP cylinder valve, shut the valve 

       off.

     - If the fire involves the cylinder, leave it alone,  

       evacuate the area and call the fire department.

     - If there is any type of fire that threatens either 

       personal safety or endangers property, call the 

       fire department.

 ·  If you notice grease or other hot material dripping 

    from the grill onto the valve, hose, or regulator, turn 

    off the gas supply immediately.  After the grill has 

    cooled, determine the cause and correct it.  After 

    cleaning the valve and hose and regulator assembly, 

     perform a leak test before continuing use.  (See Step 

13 of Assembly Instructions)

 ·  Do not operate an LP gas grill if you have knowledge  

    of or suspect a gas leak.

 ·  Never allow children to operate or play near an LP gas 

    grill.  Do not leave grill unattended.

 ·  Always turn off the LP gas cylinder at the LP cylinder 

    valve when not in use.  Allow grill to cool before

 

   handling parts or cleaning.

 ·  Do not move an LP gas grill when in use or hot.

 ·  Never touch hot surfaces.  Use heat resistant gloves, 

    long-handled tongs, or cooking mitts at all times 

    since the grill will become very hot.  Open the hood 

     carefully when cooking to avoid burns from the hot air 

and steam trapped inside.

 ·  Do not wear loose clothing (example:  hanging 

    shirt tails, clothing with frills, etc.) around a LP 

   

gas grill while in use or hot.  

 ·  Never lean your body over the LP gas grill when  

    lighting it or while it is in use or hot.

 · 

 This LP gas grill is not designed to be used with  

    more than 50% of the cooking area as a solid plate 

    (griddle).  Full coverage of plates will cause  

    excessive heat and could damage the grill.

LeakTesting

OPERATING THE LP GAS GRILL

24

Содержание Bonza Deluxe Series




































Отзывы: