background image

OPERATING AND MAINTAINING YOUR GAS GRILL

GAS, CYLINDER, HOSE AND

 REGULATOR INFORMATION

This LP gas grill was designed to use propane gas. Propane 

cylinders will supply gas all year round, even on cold winter 

days. 

LP HOSE AND REGULATOR ASSEMBLY

 

· Using a hose and regulator assembly that has 

   not been supplied by the manufacturer of this LP 

   gas grill, could result in serious bodily injury 

   or property loss.

· Use only the hose and regulator assembly that has been 

   furnished with this LP gas grill.  If the hose and regulator

   assembly is not working properly and you need a  

   replacement, contact the manufacturer (1-800-251-7558).       

· Inspect the hose before each use.  If the hose is cut or 

   damaged or shows signs of excessive abrasion or wear, 

   do not use the LP gas grill.  Contact the manufacturer, as 

   the hose must be replaced with an assembly specified by 

   

the manufacturer prior to the further use of the LP gas grill.

1) 12” diameter x 18” tall, 20 lb maximum capacity 

2) Overfill Protection Device (OPD) safety feature (should 

    be noted on cylinder) 

3) Must be constructed and marked in accordance with 

    the U.S. Department of Transportation (DOT) or the 

    National Standard of Canada, CAN\CSA-B339. (See 

    collar for marking)

4) Must have collar to protect LP cylinder valve.

· Never use an LP gas cylinder if it shows signs of: dents, 

  

gouges, bulges, fire damage, corrosion, leakage, 

  excessive rust or other forms of visual external damage; it 

  may be hazardous and should be checked by a liquid 

  

propane supplier.

· 

The LP gas cylinder should never be filled more than 80% 

  of cylinder volume. (20 lb. maximum)  Do not ask the 

  propane supplier to over-fill the cylinder.

· If you obtain LP gas through a cylinder exchange dealer,  

   make sure you are getting a safe and adequate O.P.D. 

   cylinder.  Use only a licensed LP gas cylinder dealer.

· Keep children away from LP gas cylinder at all times.

· Do not use, store, or transport the LP gas cylinder where it 

   would be exposed to high temperatures.  The relief valve 

   may open which will allow a large amount of 

flammable    gas to escape.  Never leave an LP gas cylinder 

inside a    vehicle which may become overheated by the 

sun.

· 

 WARNING!  Never store an LP cylinder indoors.  

 

   Storage of an outdoor cooking gas appliance indoors is 

   permissible only if the cylinder is disconnected and    re-

moved from the outdoor cooking gas appliance.     Cylinders 

must be stored outdoors out of the reach of    children and 

must not be stored in a building, garage, or    any other 

enclosed area.

·  

WARNING!  Never store a spare LP gas cylinder 

   under or near the grill.

 All spare and disconnected 

LP    gas cylinders must have safety caps installed on the 

LP    cylinder valve.

· LP gas is not natural gas. The conversion or attempted 

   use of natural gas in an LP unit or LP gas in a natural gas 

   unit is dangerous and will void your warranty.

· Never attempt to repair an LP gas cylinder valve yourself.  

   See an authorized LP gas cylinder dealer for repairs.

· When transporting an LP gas cylinder, keep it secured in

   an upright position with cylinder valve turned to off 

· Do not operate the LP gas grill when the LP gas 
cylinder    is not

 

attached to the cart as shown in the Asse

mbly    Instructions.

· Always check for gas leaks when you 

disconnect   and  reconnect the regulator to the LP 

gas cylinder,   especially   after a period of storage (for 

example,   over winter).

· Check tubes that lead into the burner for 

any     blockage  from insects, spiders, or food 

grease   before using.

· Check grill hoses for cracking, brittleness, holes, 

or   leaks.

· Make sure there are no sharp bends in the hose or 

  tubing.

· Make sure Regulator Hose does not contact 

hot   metal   surfaces.     

22

Connecting/ Disconnecting LP 

Gas Cylinder to Grill

·    Read and follow all warnings on LP gas cylinder.

·    If you see, smell, or hear the hiss of LP gas 

     escaping from the cylinder:

        1)  Evacuate all people from the grilling area.

        2)  Do not attempt to correct the problem 

              yourself.

        3)  Call the local fire department.

LP Gas Cylinder

· The LP gas cylinder, for use with the Aussie LP gas grills, 

   must meet the following requirements:

Содержание Bonza Deluxe Series




































Отзывы: