Aussie Bonza Deluxe Series Скачать руководство пользователя

Страница: 32 / 35

Problem

Possible Cause

Solution

Burners will not light

using the igniter

Burners not assembled cor-

rectly

Not pausing long enough

before clicking the control

panel knob

No spark

LP gas cylinder is empty
Coupling nut is not fully con-

nected to regulator
Excess flow valve tripped in

regulator

Obstructions in burners

Electrodes and burners are

wet
Wire is loose or disconnected
Wire is shorting (sparking

between igniter and elec-

trode)

Burners not assembled cor-

rectly
LP gas cylinder is empty
Excess flow valve tripped in

regulator

Coupling nut is not fully con-

nected to regulator
Obstructions in burners

Gas in LP cylinder is low

Excess flow valve tripped in

regulator

See Step 8 - Install Burners of the Assembly Instructions

When lighting the 1st (Leftmost) Burner, push-in and turn con-

trol panel knob counter-clockwise until you feel resistance with

turning. Pause 4 seconds with knob still pushed in, then con-

tinue turning knob counter-clockwise until a click is heard

Gas collector tab is bent (making too large or small of a gap

between electrode and tab). By hand, bend gas collector tab

back within a maximum of 3/16” gap to electrode. (See page 17

for illustration).
Take LP gas cylinder to licensed LP gas supplier to be refilled
Tighten coupling nut by hand about one-half to three quarters

additional turn. Do not use tools.
Turn control knobs to “off” position and turn LP gas cylinder

handle clockwise until it stops. Wait five minutes. Relight LP

gas grill.
Clean burners (See Burner Maintenance in Care and

Maintenance section of this manual)
Dry electrode with clean cloth

Reconnect the wire
Replace igniter wire/electrode assembly (Call the Customer

Service Department)

See Step 8 - Install Burners page of the Assembly Instructions

Take LP gas cylinder to licensed LP gas supplier to be refilled
Turn control knobs to “off” position and turn LP gas cylinder

handle clockwise until it stops. Wait five minutes. Relight LP

gas grill.
Tighten coupling nut by hand about one-half to three quarters

additional turn. Do not use tools.
Clean burners (See Burner Maintenance in Care and

Maintenance section of this manual)

Check LP gas cylinder. Refill if necessary.

Turn control knobs to “off” position and turn LP gas cylinder

handle clockwise until it stops. Wait five minutes. Relight LP

gas grill. If flame remains to be low, turn off gas at cylinder

and grill. Disconnect the regulator from the LP gas cylinder.

Reconnect the regulator to the LP gas cylinder. Perform a leak

test. Relight grill. This will reset the excess flow valve.

Burners will not light

using a match

Low flame or low heat

Содержание Bonza Deluxe Series




































Результаты поиска

Содержание Bonza Deluxe Series

Отзывы:

Похожие инструкции для Bonza Deluxe Series

Бренды по названию

Популярные бренды

Aussie Bonza Deluxe Series, Руководство пользователя

Результаты поиска

Содержание Bonza Deluxe Series

Отзывы:

Похожие инструкции для Bonza Deluxe Series

Бренды по названию

Популярные бренды