Aussie 7202 Скачать руководство пользователя

Страница: 9 / 36

STEP 1- WHEEL LEG/ SIDE TABLE ASSEMBLY

TOOLS:

•Note: There are three side table designs used depending on the model: Square SideTables (Item 1) which can be used

on either side, Left and Right Teardrop Side Tables (Item 2 & 3), or Deluxe Side Tables (Item 4).

•Lay Left Side Table (depending on your model you have either 1, 2, or 4) upside down on flat surface as

shown. Locate the two Wheel Legs which are the shorter legs with a large axle hole at one end.

•On models with wooden legs, place Rear Wheel Leg so four large recessed holes face away from Side Table

(Fig. A) and two threaded holes in edge of leg point outward. (Fig. B)

• Insert four 1/4” x 1” (1/4” x 1 3/8” for Metal

legs) Bolts through the leg into the threaded
holes of Side Table. (Fig. A) Do not tighten
bolts completely.

• Attach Front Wheel Leg to Left Side Table in

the same way. On models with wooden legs
make sure the two threaded holes on the
edge of each leg face outward. Make sure
the three velcro patches face inside on all
models.

FIG. B

THREADED HOLES IN LEGS
(Deluxed Models with Metal legs do
not have these threaded holes and
can be oriented either way.)

AXLE HOLES
(WHEEL LEGS)

FRONT WHEEL
LEG - THREE
VELCRO
PATCHES FACE
INSIDE

SIDE TABLE
(TEARDROP
TABLE
SHOWN)

REAR WHEEL LEG

KANGA, BONZA - WOOD

BONZA DELUXE - METAL

FIG. A

FOUR LARGE
RECESSED HOLES
(Wooden Legs Only)

1/4” x 1” BOLT

(ITEM 9) ACTUAL SIZE
1/4” x 1” BOLT 8 pcs

(1/4” X 1 3/8” Deluxe Models)

(ITEM 1, 2, or 4) SIDE TABLE

(ITEM 6) FRONT WHEEL LEG - WOOD

(ITEM 5) REAR WHEEL LEG - WOOD

(ITEM 8) FRONT WHEEL LEG - METAL TUBING

(ITEM7) REAR WHEEL LEG - METAL TUBING

(ITEM 10) ACTUAL SIZE
1/4” X 1 3/8” BOLT 8pcs

Содержание 7202





































Результаты поиска

Содержание 7202

Отзывы:

Похожие инструкции для 7202

Бренды по названию

Популярные бренды

Aussie 7202, Инструкция по сборке и использованию

Результаты поиска

Содержание 7202

Отзывы:

Похожие инструкции для 7202

Бренды по названию

Популярные бренды