background image

It is not necessary to remove and wash the ceramic bri-
quettes in order to keep them clean. Burning off the residue
after each cooking should be sufficient. Heavily impregnated
ceramic briquettes should be turned over so that the dirty
side faces the burners in order to burn off any residue.

·  Always turn the LP gas cylinder valve “Off” when 

not in use. Allow grill to cool before handling parts 
or cleaning.    

·  Empty the foil pan and grease tray after each 

cooking session so excessive grease does not 
accumulate. Failure to remove  grease may result in
grease dripping onto the cart and/or a grease fire in
the tray.

·  Never light the LP gas grill without the foil pan and

grease tray in place.

· Before each use, check your Bottom Panel, Grease Tray, 

and Foil Pan. If there is excessive grease buildup, clean 
and replace. 

· Make sure Bottom Panel, Grease Tray, & Foil Pan are in 

place before each grilling session. 

· Failure to remove grease from the Foil Pan may result in  

grease dripping onto cart and/or a grease fire in tray.

·

The Foil Pan can be cleaned or replaced with a standard 

size foil pan (apprx. 5-1/2” W. x 8-1/2” L. x 1-1/8” H.) 
found at your local grocer.   

·  Always turn off the LP gas cylinder at the LP 

cylinder valve when not in use. Allow grill to cool 
before handling parts or cleaning.    

How to Clean the Grill Body

1) Remove cooking surfaces and burners before full 

cleaning. 

2) Remove excess grease and/or fat from the grill body 

with a soft plastic or wooden scraper.  Never use steel 
wool or other abrasive cleaning product on porcelain 
coated surfaces. It is not necessary to remove all the 
grease from the body.  

3) For further cleaning, use hot soapy water and a cloth, or 

nylon-bristled brush only.  

Do not immerse the gas 

controls or manifold in water. 

4) When finished cleaning, replace burners and cooking 

surfaces according to Steps 9, 10, and 11 in the 
Assembly Instructions.

5) Check burner operation after reassembly.

·  Always turn off the LP gas cylinder at the LP 

cylinder valve when not in use. Allow grill to cool 
before handling parts or cleaning.

·  Do not use aerosols or store flammable liquids or 

materials near this gas grill.

·  Never apply polyurethane to the wood cart while 

grill is in use or hot.  Allow polyurethane to 
completely dry before further use.

Your Cart is manufactured using a hardwood ideally suited 
to outdoor use. To maintain its condition and appearance, 
annual application of polyurethane is recommended.  

· Follow all instructions and warnings listed on the 

polyurethane container.

· Always use a brush to apply the polyurethane, do not 

use a spray can. 

· Do not apply polyurethane to the metal grill body.
· Using the Grill Storage Cover (55) will help maintain  

the appearance of your grill and protect the finish. 

In addition to the above Care and Maintenance Instruction,
periodically check and tighten all nuts, bolts, and screws.

· Never store an LP gas cylinder indoors (empty or 

filled).  If storing the gas grill indoors, disconnect

the LP gas cylinder and store it outdoors out of the
reach of children.

· Never leave an LP gas cylinder inside a vehicle

which may become overheated by the sun.

· Never store a spare or disconnected LP gas 

cylinder under or near the LP gas grill.

· Always turn off the gas cylinder when not in use.

Allow grill to cool before handling parts or   
cleaning.

· Even though your LP gas cylinder may appear to be

empty, gas may still be present and the cylinder 

should be transported and stored accordingly.

· Store your LP gas grill in a cool dry place .
· Disconnect LP gas cylinder from grill and store outside, in

a dry, well-ventilated area, away from any sources of heat
or ignition. Re-cap LP cylinder valve with the Safety Cap. 

· Remove burners and wrap with aluminum foil to prevent 

insects from entering the burner holes. Store wrapped 

burners on top of the cooking grids.    

· Before next use, remove aluminum foil and reinstall 

burners, Ceramic Briquettes, and grids according to Step 9,
10, and 11 of Assembly Instructions.

· Check your LP gas grill for gas leaks, deterioration, proper

assembly, and burner obstructions before using the grill
after periods of storage and/or non-use(i.e. over winter).

Ceramic Briquettes

Bottom Panel/ Grease Tray

Cleaning the Grill Body

Caring for the Wood Cart

Preventive Maintenance

Storage

32

Содержание 7202





































Отзывы: