background image

                                                              

 

                               

                     

DEMO XTR-8LR100 

DEMO XTR-8LR10

 

                          User Manual

 

 

 
Le caratteristiche  tecniche possono subire variazioni senza preavviso. AUR°EL S.p.A. non si assume la responsabilità di danni causati dall’uso improprio del dispositivo.

 

 

AUR°EL S.p.A. Via Foro dei Tigli, 4 - 47015 Modigliana (FC) – ITALY 
Tel.: +39.0546.941124  Fax: +39.0546.941660

 

http://www.aurelwireless.com

  -  email: 

[email protected]

 

                                                                Rev 2.2  17/05/2016

 

Page  

11

 of 

17

 

 

In the following screens of Realterm, the transmission of unit 1 to 2 is displayed, of the string "Demo-board 
unit1  XTR-8LR100",  the  hexadecimal  characters  (0x0001)  of  the  sender  address  are  not  displayed  by 
Realterm for incompatibility of contemporary display to ASCI characters and HEX (screen on the right). 
 
Note the string-field "Send ASCII" (screen on the left) formatting the message before the addressee address 
"\ x0 \ x2" followed by payload "Demo-board unit1 XTR-8LR100". 
 

 

 

Unità1 port57 sends to unit 2 
\x0 \x2 Demo-board unit1 XTR-8LR100     
 

Unità2 port58 receives from unit 1 
\x0 \x1 Demo-board unit1 XTR-8LR100 
 

 

Screens displayed by Realterm for the message "Demo-board unit2 XTR-8LR100" sent from unit 2 to 1 
 

 

 

Unit 1 port57 receives from unit 2 
\x0 \x2 Demo-board unit2 XTR-8LR100     
 

Unit 2 port58 sends to unit 1 
\x0 \x1 Demo-board unit2 XTR-8LR100 
 

 

 
 
 
 
 
 

Содержание DEMO XTR-8LR10


















Отзывы: