AURATON S14, Руководство пользователя

Страница: 23 / 28

23 22
AUTO operation mode
During normal operation, when the controller attempts to reach the
temperature value set in the "
D
" section, the AUTO text is displayed. At
that time, the fan is working at full power (programmed as a percentage)
until the set value is reached. After the temperature is reached, the fan
switches to periodic operation (with breaks between blow-throughs).
6.2.5. Furnace extinguishing function
If the temperature on the SR1 sensor drops below the preset value (the
factory setting is 30°C) for at least 30 minutes, then the fan is stopped
definitively and the display shows the blinking text
STOP LO . The fan
leaves the definitive switch off state automatically when the temperature
measured by the
SR1 sensor increases above 30 °C.
The definitive fan switch off temperature can be set in the range of 15 °C
to 40°C. To do so, press the "
D
" button and display the fan temperature. If
you press the "
D
" button again, the fan operation time and the break
time settings will be displayed. By pressing the "
D
" button yet again (the
shut-down temperature and the STOP LO text are displayed), you can set
the definitive fan switch-off temperature.
Using the "+" (increase) and "-" (decrease) buttons, you can set the
desired temperature value. Once the desired temperature value is set, it
must be confirmed (saved) within 10 seconds by pressing the "
OK "
button.
Otherwise, the changed setting will not be saved and the controller will
return to the previous setting.
6.2.6. Changing the hysteresis
To change the hysteresis value, press the "
D
" button and display the fan
temperature. If you press the "
D
" button again, the fan operation time
and the break time settings will be displayed. By pressing the "
D
" button
yet again, you will display the definitive fan switch-off temperature and
the
STOP LO text. Press the "D" button one more time and use the "+" or
"-" button to set the desired hysteresis value. Once the desired
temperature value is set, it must be confirmed (saved) within 10 seconds
by pressing the "
OK " button. Otherwise, the changed setting will not be
saved and the controller will return to the previous setting.
Example: Then the temperature setting is 40°C and the hysteresis setting
is 4°C, the fan is permanently switched on when the temperature drops
below 38°C and moves to periodic operation when the temperature
reaches 42 C.
6.2.8. Setting the fan's soft start time
AURATON S14 enables setting the time within which, after its start, the
fan will reach its full power (the percentage value that has been set - see
item 6.2.7. Setting the maximum fan power value). It is possible to set the
fan's soft start time in the range of 0 seconds (start with the full set power)
to 15 seconds, after which the fan reaches its full preset power. The value
can be set using the "+" (increase) or "-" (decrease) buttons. Once the
desired temperature value is set, it must be confirmed (saved) within 10
seconds by pressing the "
OK
" button.
Otherwise, the changed setting will not be saved and the controller will
return to the previous setting.
6.2.7. Setting the maximum fan power value
The controller has a function that enables fixing the maximum fan power
as a percentage value. The fan power can be set in the range of 30% to
100% (where 100% is the maximum fan power value). In order to change
the fan power, press the "
D
" button and display the fan temperature. If
you press the "
D
" button again, the fan operation time and the break
time settings will be displayed. By pressing the "
D
" button yet again, you
will display the definitive fan switch-off temperature and the STOP LO
text. Press the "
D
" button one more time and set the desired hysteresis
value.
After you press the "
D
" button again, you can set the maximum fan
power (the displayed factory-set value is 100%).
Use the "+" (increase) or "-" (decrease) buttons to set the desired value of
fan power. Once the desired temperature value is set, it must be
confirmed (saved) within 10 seconds by pressing the "
OK " button.
Otherwise, the changed setting will not be saved and the controller will
return to the previous setting.
NOTE: Maximum fan power in the range of 30% to 100% means that the
fan will also be in operation during ignition with the preset value of
power.
6.2.9. Manual mode - continuous operation
In order to manually switch on the fan (regardless of the current
temperature at the
SR1 sensor), press the "
D
" button for 3 seconds. The
display will then show the " " sign next to the fan symbol. If you wish to
switch off the fan's manual operation, press the "
D
" button again and
hold it pressed for 3 seconds.