manualshive.com logo in svg

AUMA SVM 05.1, Руководство по эксплуатации

Поделиться
Скачать
AUMA SVM 05.1 Скачать руководство пользователя страница 3

22

8.

Operation................................................................................................................................

22

8.1.

Manual operation

22

8.2.

Motor operation

22

8.2.1.

Local actuator operation

23

8.2.2.

Actuator operation from remote

25

9.

Commissioning (basic settings of controls).......................................................................

25

9.1.

Cover to controls: open

25

9.2.

Setting via hardware (switches) or via software

26

9.3.

Type of seating: set

27

9.4.

Torque switching: set

28

9.5.

Fieldbus address (slave address), baud rate, parity and monitoring time: set

30

9.6.

Termination resistor: connect

30

9.7.

Output speed: set

32

9.8.

Cover to controls: close

33

10.

Commissioning (basic settings at actuator)........................................................................

33

10.1.

End position detection: verify setting

33

10.2.

End position detection: set again via local controls

34

10.2.1.

End position CLOSED: set again

34

10.2.2.

End position OPEN: set again

35

10.3.

Switch compartment: open

35

10.4.

Potentiometer setting 

37

10.5.

Mechanical position indicator: set

37

10.6.

Switch compartment: close

38

11.

AUMA CDT software (accessories).......................................................................................

39

12.

Corrective action....................................................................................................................

39

12.1.

Fault indications and warning indications

40

12.2.

Fuses

40

12.2.1.

Fuses within the actuator controls

40

12.2.2.

Motor protection (thermal monitoring)

41

13.

Servicing and maintenance...................................................................................................

41

13.1.

Preventive measures for servicing and safe operation

41

13.2.

Maintenance 

41

13.3.

Disposal and recycling

42

14.

Technical data.........................................................................................................................

42

14.1.

Technical data Globe valve actuator

46

15.

Spare parts.............................................................................................................................

46

15.1.

Globe valve actuators SVM 05.1 – SVM 07.5/SVMR 05.1 – SVMR 07.5

48

16.

Certificates..............................................................................................................................

48

16.1.

Declaration of Incorporation and EC Declaration of Conformity

51

Index........................................................................................................................................

53

Addresses...............................................................................................................................

3

SVM 05.1 – SVM 07.5 / SVMR 05.1 – SVMR 07.5 
Modbus RTU 

Table of contents

Содержание SVM 05.1

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды