manualshive.com logo in svg

AUMA SVM 05.1, Руководство по эксплуатации

Поделиться
Скачать
AUMA SVM 05.1 Скачать руководство пользователя страница 32

Table 15:

Examples of possible settings

SVM/SVMR 07.5

SVM/SVMR 05.1/07.1

Output speed

Output drive

[rpm]

Output speed

Motor

[rpm]

Output speed via parameter:

Speed LOCAL
Speed REMOTE

or via fieldbus:
(

Speed fieldbus

 = 

External

)

Output speed

Output drive

[rpm]

Output speed

Motor

[rpm]

Output speed via parameter:

Speed LOCAL
Speed REMOTE

or via fieldbus:
(

Speed fieldbus

 = 

External

)

0.6

133

0.0 %

1.6

133

0.0 %

0.8

186

2.0 %

2.2

176

2.0 %

1.1

255

6.0 %

3.2

256

6.0 %

1.6

371

11.0 %

4

320

9.0 %

2.2

510

18.0 %

5.6

448

15.0 %

3.2

742

29.0 %

8

640

24.0 %

4.0

928

38.0 %

11

880

35.0 %

5.6

1,299

55.0 %

16

1,280

54.0 %

8.0

1,856

81.0 %

22

1,760

77.0 %

9.7

2,250

100.0 %

28.1

2,250

100.0 %

9.8.

Cover to controls: close

1.

Clean sealing faces of housing and cover.

2.

Apply a thin film of non-acidic grease (e.g. petroleum jelly) to the sealing faces.

3.

Check whether seal is in good condition, replace seal if damaged.

4.

Apply a thin film of non-acidic grease (e.g. petroleum jelly) to the seal and insert
it correctly.

5.

Place cover [1].

6.

Fasten screws evenly crosswise.

32

 SVM 05.1 – SVM 07.5 / SVMR 05.1 – SVMR 07.5

Commissioning (basic settings of controls)

 Modbus RTU

Содержание SVM 05.1

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды