AUMA PROFOX PF-M100 Скачать руководство пользователя

Страница: 10 / 48

Transport and storage

4.1.

Transport

For transport to place of installation, use sturdy packaging.

Hovering load!

Death or serious injury.

→

Do NOT stand below hovering load.

→

Attach ropes or hooks for the purpose of lifting by hoist only to housing and NOT
to handwheel.

→

Actuators mounted on valves: Attach ropes or hooks for the purpose of lifting
by hoist to valve and NOT to actuator.

→

Actuators mounted to gearboxes: Attach ropes or hooks for the purpose of lifting
by hoist only to the gearbox using eyebolts and NOT to the actuator.

→

Respect total weight of combination (actuator, gearbox, valve)

→

Secure load against falling down, sliding or tilting.

→

Perform lift trial at low height to eliminate any potential danger e.g. by tilting.

4.2.

Storage

Danger of corrosion due to inappropriate storage!

→

Store in a well-ventilated, dry room.

→

Protect against floor dampness by storage on a shelf or on a wooden pallet.

→

Cover to protect against dust and dirt.

→

Apply suitable corrosion protection agent to uncoated surfaces.

Long-term storage

For long-term storage (more than 6 months), observe the following points:

Prior to storage:
Protect uncoated surfaces, in particular the output drive parts and mounting
surface, with long-term corrosion protection agent.

At an interval of approx. 6 months:
Check for corrosion. If first signs of corrosion show, apply new corrosion protec-
tion.

PROFOX / PF-M25 – PF-M100

Transport and storage

Profibus DP

Содержание PROFOX PF-M100

















































Результаты поиска

Содержание PROFOX PF-M100

Отзывы:

Похожие инструкции для PROFOX PF-M100

Бренды по названию

Популярные бренды

AUMA PROFOX PF-M100, Руководство по эксплуатации

Результаты поиска

Содержание PROFOX PF-M100

Отзывы:

Похожие инструкции для PROFOX PF-M100

Бренды по названию

Популярные бренды