manualshive.com logo in svg

AUMA NORM SQ 05.2, Руководство по эксплуатации и инструкция

Поделиться
Скачать
AUMA NORM SQ 05.2 Скачать руководство пользователя страница 40

Service conditions

Indoor and outdoor use permissible

Use

Any position

Mounting position

≤

 2,000 m above sea level

> 2,000 m above sea level, please contact AUMA

Installation altitude

–40 °C to +80 °C (part-turn actuators for open-close duty with 3-phase AC mo-
tors)
–40 °C to +70 °C (part-turn actuators for open-close duty with 1-phase AC mo-
tors)
–40 °C to +60 °C (part-turn actuators for modulating duty)

Standard:

Ambient temperature

–60 °C to +60 °C
0 °C to +120 °C (part-turn actuators for open-close duty with 3-phase AC motors)

Options:

For actual version, refer to actuator name plate.

IP68 with AUMA 3-phase AC motor/1-phase AC motor
For special motors differing enclosure protection: refer to name plate.

Standard:

Enclosure protection according
to EN 60529

DS Terminal compartment additionally sealed against interior (double sealed)

Option:

According to AUMA definition, enclosure protection IP68 meets the following requirements:

●

Depth of water: maximum 8 m head of water

●

Duration of continuous immersion in water: Max. 96 hours

●

Up to 10 operations during continuous immersion

Modulating duty is not possible during continuous immersion.

For actual version, refer to actuator name plate.

Pollution degree 4 (when closed) according to EN 50178

Pollution degree

2 g, from 10 to 200 Hz
Resistant to vibration during start-up or for failures of the plant. However, a fatigue strength
may not be derived from this. Valid for part-turn actuators in version AUMA NORM (with
AUMA plug/socket connector, without actuator controls). Not valid in combination with
gearboxes.

Vibration resistance according
to IEC 60068-2-6

KS: Suitable for installation in industrial units, in water or power plants with a
low pollutant concentration as well as for installation in occasionally or perman-
ently aggressive atmosphere with a moderate pollutant concentration (e.g.
wastewater treatments plants, chemical industry)

Standard:

Corrosion protection

KX: Suitable for installation in extremely aggressive atmospheres with high hu-
midity and high pollutant concentration

Option:

KX-G : same as KX, however aluminium-free version (outer parts)

Powder coating

Finish coating

AUMA silver-grey (similar to RAL 7037)

Standard:

Colour

Other colours are possible on request.

Option:

AUMA part-turn actuators meet or even exceed the lifetime requirements of EN 15714-2.
Detailed information can be provided on request.

Lifetime

Further information

Electromagnetic Compatibility (EMC): (2004/108/EC)
Low Voltage Directive: (2006/95/EC)
Machinery Directive: (2006/42/EC)

EU Directives

40

 SQ 05.2 – SQ 14.2/SQR 05.2 – SQR 14.2

Technical data

Содержание NORM SQ 05.2

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды