manualshive.com logo in svg

auer 753020, Руководство по установке

Поделиться
Скачать
auer 753020 Скачать руководство пользователя страница 25

-  

INSTALLATION

 

 PILOT 

-C14-

MANUAL

- 

25

7.2.7 - Errors indicated by the pilot

Press 

 to stop the sound signal (the error persists)

Display

Error

Possible causes

Consequences

Reset

AIR hp

T_air error

The heat pump temperature sensor (Tair) is defective 

or not connected properly.

- Check Cable and Probe Connector Status

- Check the ohmic value of the probe

- Replace probe if fault is found

heat pump stopped

automatic after repair

CIRC pump

Power cable or PWM 

circulator cable error

The cables for the circulator (heating/water) are 

defective or not connected properly.

- Check PWM cable connection to circulator

- Check power cable connection

- For installations equipped with a underfl oor heating, 

check for a possible power cut by the underfl oor 

heating safety (LTP)

complete stop

manual

AMBI eNCE

Amb error

The ambient temperature sensor is defective

(error when measuring the ambient temperature)

heating circuit stopped

automatic after repair

BLOc. Circ

Circulator pump blocked

The circulator (heating/water) is blocked or is working 

with a load loss which is too high.

- Check that na valves are closed on the circuit

- Check the status of the fi lter

- Reset and verify that the circulator rotates with a 

screwdriver and the central circulator screw

complete stop

manual

BUS

BUS

BUS communication error.

- Check BUS connection between heat pump and 

hydraulic pilot

- Verify that the BUS cable is routed away from 

power cables or other disturbance sources (neons, 

appliances, ... )

complete stop

automatic after repair

amb bus

Amb BUS error

The ambient temperature sensor («Amb» terminals on 

the pilot) is defective or not connected properly

heating circuit stopped

automatic after repair

cond. senso

          diag

Condenser fl uid pressure 

sensor error

The refrigerant circuit pressure sensor is defective or 

not connected properly

operation in downgraded mode automatic after repair

evap. senso

Evaporator fl uid pressure 

sensor error

The refrigerant circuit pressure sensor is defective or 

not connected properly

heat pump stopped

automatic after repair

pres, senso

Pressure sensor error

The heating water pressure sensor is defective or not 

connected properly

complete stop

automatic after repair

invr. comm.

Inverter communication error

HP circuit board is disconnected or defective

- Check condition of internal wiring to heat pump

heat pump stopped

manual

CP CTRL

Loss of control of inverter

Error detected by the HP circuit board.

Wait about 20 minutes before rearming and make a 

reading on USB key if the fault occurs again.

heat pump stopped

manual

CP ELEC

Inverter having electrical 

problems

Error detected by the HP circuit board.

Wait about 20 minutes before rearming and make a 

reading on USB key if the fault occurs again.

heat pump stopped

manual

CP MECA

Inverter having mechanical 

problems

Error detected by the HP circuit board.

Wait about 20 minutes before rearming and make a 

reading on USB key if the fault occurs again.

heat pump stopped

manual

CP THERM

Inverter having thermal 

problems

Error detected by the HP circuit board.

Wait about 20 minutes before rearming and make a 

reading on USB key if the fault occurs again.

heat pump stopped

manual

CP1  ovrht.

ERR

Multiple overheatings on 

compressor 1

-  The set temperature for heating during warmer 

months is too high

- Problem with refrigerant fl uid load

heat pump stopped

manual

CP2  ovrht.

ERR

Multiple overheatings on 

compressor 2

-  The set temperature for heating during warmer 

months is too high

- Problem with refrigerant fl uid load

heat pump stopped

manual

Содержание 753020













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды