background image

128-8782b

10 of 12

Page 10

The parking lights will flash and the siren will chirp 4 times indicating the
timed start mode is activated.

CANCELING THE AUTOMATIC START UP TIMER

To cancel the automatic start up timer do one of the following;

1. Start the vehicle manually with the use of the ignition key and depress

the brake pedal.

2. Remote start the vehicle using your keychain RF transmitter.

3. Shut off the vehicle using the keychain transmitter by pressing and re-

leasing the trunk/key transmitter button 2 times.

TELEMATIC UPGRADE:

This system has the ability to have a telematic upgrade module connected
to it. This is an upgrade that can give you control of certain functions of your
vehicle from a Telephone, or in some cases a computer interface. Please
check with your installation center for most recent Telematic Upgrades. If
you had a Telematic Upgrade installed, the manual supplied with the up-
grade unit will provide a operators manual advising of the features of the
system and means available to control these features of your vehicle.

PROGRAMMED TRANSMITTER NOTIFICATION (PTN)

Every time after Disarm when the ignition key is turned on, the unit's LED
will report the number of transmitters programmed into the system.  This
safety feature will alert you if an unauthorized transmitter has been
programmed into your vehicle's security system without your knowledge.
Typical from the factory, there will be a 2 flash, pause, repeated 3 times
indicating that two transmitters are programmed into the system.  If you
note additional flashes, there may heve been an additional transmitter
added without your knowledge or authorization.  If you notice a change in
the transmitter LED report pattern, you can correct this by looking up
how to erase and reprogram your transmitters found in the transmitter
programming guide. This reprogram operation will erase all unauthorized
or unwanted transmitters.

Содержание Platinum+ APS 687C













Отзывы: