background image

128-8782b

4 of 12

Page 4

beep for 30 seconds or until the button is activated again for 3 seconds or
any other button is operated.

NOTE:

  This system has the ability to unlock the drivers door with the first

press of the unlock transmitter button and then unlock all other
doors when the unlock button is pressed a second time. This op-
tional feature may require additional components.  Consult your
installation center to determine if this feature has been added to
your vehicle.  Additionally this system can be programmed to auto-
matically lock and unlock the doors with the turning on and off of
the ignition key.

ADDITIONAL REMOTE FUNCTION (CHANNEL 3)

This system has an additional feature that can be connected to a number
of different optional accessories. Some of the more common uses for this
channel are:



Remote Trunk Release



Remote Window Closure



Remote Garage Door Interface

To activate the optional accessory, press and hold the trunk/key button on
the keychain transmitter for four seconds.

NOTE:

  The feature that has been added to channel 3 will always be acti-

vated using the  same transmitter button that remotely starts the
vehicle. There is no way to move the channel 3 function to a differ-
ent transmitter button.

ADDITIONAL REMOTE FUNCTION (CHANNEL 4)

This system has an additional feature that can be connected to a number
of different optional accessories. Some of the more common uses for this
channel are:

 Can Be Set Up To Activate Rear Window Defogger

      During Remote Start If Vehicle Is So Equipped

 Remote Window Closure

 Rear Hatch Release

 Right Or Left Slider Doors in An Equipped Van

To activate the optional accessory, press the option button on the
keychain transmitter.  The optional accessory will immediately engage.

Содержание Platinum+ APS 687C













Отзывы: