CrimeStopper CoolStart RS-1604TW1 Installation Instructions Manual Download | Manualshive

Page: 1 / 28

background image

RS-1301DP/1303DP/1304DP 1 WAY SYSTEMS
RS-1604TW1/1704TW2/1804FM 2-WAY SYSTEMS
RS-1300DP ADD-ON MODULE

DP SERIES II (Data port)

REMOTE ENGINE STARTING SYSTEM

INSTALLATION INSTRUCTIONS

INTRODUCTION

CONGRATULATIONS

on your choice of a “Cool Start” System with Data Port Technology for direct connection for bypass

module by Crimestopper Security Products Inc. This booklet contains the information necessary for installing your remote
starter system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech
Support number below.

Note: Some features will not be available on units with 1 button, 2 button, and 3 button remotes.

DISCLAIMER

:

This installation book is designed for the installer or individual with an existing understanding of automotive electrical
systems, along with the ability to test and connect wires for proper operation. To ease installation, we suggest that you

READ THIS MANUAL

before beginning your installation. This book is provided as a GENERAL GUIDELINE and the

information contained herein may differ from your vehicle. Crimestopper Security Products, Inc. and its’ vendors shall not
be liable for any accident resulting from the use of this product. This system is designed to be professionally installed into
a vehicle in which all systems and associated components are in perfect working condition.

TECHNICAL SUPPORT: (800) 998-6880

Monday - Friday 8:00am - 4:30pm Pacific Std. Time
Web Site: www.crimestopper.com
E-mail: [email protected]

CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063

REV D 10.2006

This device complies with FCC Rules part 15.  Operation is subject to
the following two conditions:  (1) This device may not cause harmful
interference, and (2) This device must accept any interference that
may be received, including interference that may cause undesired
operation.  The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
Such  modification  could  void  the  user’s  authority  to  use  the
equipment.

1
2
3
...
»

Summary of Contents for CoolStart RS-1604TW1





























Reviews:

No comments

Related manuals for CoolStart RS-1604TW1

Brand: Oppermann Regelgeräte Pages: 3

Brand: TFA Pages: 48

Brand: Eldes Pages: 10

Brand: Sonic Alert Pages: 5

Brand: Kidde Pages: 11

Brand: Directed Electronics Pages: 20

Brand: stabo Pages: 12

Brand: Deltronic Security Pages: 9

Prestige Platinum 128-4627A

Brand: Audiovox Pages: 21

Brand: Prestige Pages: 8

Brand: Honeywell Home Pages: 4

Brand: Datexx Pages: 1

Brand: Quell Pages: 18

Brand: Teknim Pages: 2

Brand: i-box Pages: 88

Automobile Alarm

Brand: Pro-tec Pages: 16

Brand: Code Alarm Pages: 18

Pursuit PRO9051E

Brand: Voxx Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands